 |
 |
 |
 |
BendPak HD-9AE 9,000 lb. Capacity Alignment Lift
The HD-9AE four-post car lifting and alignment system features adjustable multi-position leveling, integrated front radius plates and rear slip plates, making it compatible with all leading alignment instrumentation including 3D and camera wheel alignment systems.
- Multi-caster slip plates in the back and radius plates up front allow for extremely precise, free-floating alignment.
- Dual radius plate positions for better vehicle accommodation.
- Heavy-duty stainless-steel lifting cables provide a great balance of strength, abrasion resistance and fatigue.
- Dual-hub cable sheaves reduce stress, fatigue and wear.
- Grease nipples are located on every sheave and sheave axle to make lubrication maintenance a breeze.
- The HD-9AE features a single hydraulic cylinder hidden away under the runway for maximum performance and reliability and minimum exposure to elements.
- An integrated hydraulic flow restrictor provides a controlled descent in the unlikely event of an unexpected hose rupture.
- A durable powder coat finish can withstand harsh environments and chemical spills and will provide years of protection.
- Spring-loaded safety locks automatically engage continuously during rise and adjustable safety ladders allow for precise runway leveling even when installed on sloped floors.
- A simple push-button pneumatic lock release makes lowering operations simple and fast. Aircraft-quality stainless steel and aluminum pneumatic cylinders will provide years of trouble-free service.
- A secondary lock system is on constant guard and acts as a slack-cable device in the unlikely event of an unexpected cable failure.
- Lifting cables, airlines, safety latches and sheaves are all fully enclosed within lift structure.
- Features multiple adjustable height locking positions for variable-height parking and infinite leveling.
- A maintenance-free electric hydraulic power system assures ultimate dependability.
- All operator controls are conveniently located within easy reach.
- Non-skid runways provides maximum grip, even when the runway surface is wet or oily.
Optional 4,500 lb. capacity rolling jacks (model RJ-45) make a great addition to increase service capacity. Each jack features three safety-lock positions and stackable truck and van adapters for increased lifting height and better access to frame contact points on high ground-clearance vehicles. The jacks come equipped with a commercial grade air-hydraulic pump requiring a maximum pressure of 125 PSI and 10-20 CFM.
Specifications
|
HDS-9AE
|
Lifting Capacity*
|
9,000 Lbs.
|
Overall Width
|
127" / 3,226 mm
|
Outside Length
|
198" / 5,029 mm
|
Overall Length
|
224" / 5,690 mm
|
Height of Columns
|
88" / 2,235 mm
|
Min. Runway Height
|
6-1/2" / 165 mm
|
Max. Rise
|
70" / 1,778 mm
|
Max. Lifting Height
|
76-1/2" / 1,943 mm
|
Width Between Posts
|
117" / 2,972 mm
|
Runway Width
|
19" / 483 mm
|
Width Between Runways
|
40" / 1,016
|
Length of Runways
|
188" / 4,775 mm.
|
Min Wheelbase @ Rated Capacity
|
135" / 3,429 mm
|
Min Wheelbase @ 75% Capacity
|
115" / 2,921 mm
|
Min Wheelbase @ 50%Capacity
|
95" / 2,413 mm
|
Min Wheelbase @ 25% Capacity
|
80" / 2,032 mm
|
Locking Positions
|
12
|
Lock Spacing
|
Every every 4" / 102 mm
|
Lifting Time
|
60 Seconds
|
Motor
|
220 VAC / 60 Hz. 1Ph.
|
Note: An air supply (minimum: 30 psi / 3 CFM) is required for the safety-lock mechanisms to disengage. It is solely the responsibility of the end-user to provide, install and maintain the air supply.
*Not all BendPak lift models meet the standards as prescribed by ANSI/ALI ALCTV-2006 or ANSI/UL 201. Consult
www.autolift.org for a complete list.
Better Products ¨C Better Service ¨C Better Value
Duration: From the date of purchase by the original Purchaser or 60-24-12 months from the date of shipment by BendPak or whichever comes first.
a Five Years (60-Months) Bumper-to-Bumper Warranty on the lift structure
a Two Years (24-Months) Warranty on the hydraulic cylinder(s) and power unit
a One Year (12-Months) Labor Warranty on site or at factory
a One Year (12-Months) Free-Shipping* on ground-freight charges related to warranty performance
Limited Warranty
- Who gives this warranty (Warrantor): BendPak Inc., 1645 Lemonwood Dr. Santa Paula, CA 93060
- Who receives this warranty (Purchaser): The original Purchaser (other than for purpose of resale)
- What products are covered by this warranty: Any BendPak Two-Post or Four-Post car lift**
- What is covered under this warranty: manufacturer defects due to material and/or workmanship with the exceptions noted below.
- What is not covered under this warranty:
- Any failure that results from Purchaser¡¯s abuse, neglect or failure to operate, maintain or service product in accordance with instructions provided in the owner¡¯s manual(s) supplied
- And damage caused by overloading lift beyond rated capacity
- Items or service normally required to maintain the product, i.e. lubricants, oil, etc.
- Items considered general wear parts such as rubber pads, lifting cables, etc. unless wear or failure is a direct result of manufacturer defect due to material and/or workmanship
- Any component damaged in shipment or any failure caused by installing or operating lift under conditions not in accordance with installation and operation guidelines or damaged by contact with tools or surroundings
- Motor or pump failure caused by rain, excessive humidity, corrosive environments or other contaminants
- Rusted components due to improper maintenance or corrosive environments
- Cosmetic defects that do not interfere with product functionality
- Damage due to incorrect voltage or improper wiring
- Any incidental, indirect, or consequential loss, damage, or expense that may result from any defect, failure, or malfunction of BendPak Inc product
- Responsibilities of Warrantor under this warranty: Repair or replace, at Warrantor¡¯s option, component which is defective, has malfunctioned and/or failed to conform within duration of the warranty period. BendPak Inc. will pay reasonable labor costs for the first 12 months only
- Responsibilities of Purchaser under this warranty:
- Provide dated proof of purchase and maintenance records
- In some cases, components may be required to be shipped to the nearest BendPak Authorized Service Center. Freight costs, after 12-months, must be borne by the Purchaser.
- Use reasonable care in the operation and maintenance of the products as described in the owner¡¯s manual(s).
- When Warrantor will perform repair or replacement under this warranty: Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts.
*Free-shipping applies to direct shipping points within the 48 continental United States. Rural area shipping surcharge may apply for remote addresses. **For all BendPak brand two-post and four-post surface mounted lifts manufactured on or following 1/1/2011.
Limitation of Liability
In no event will either party be liable for any damage caused by the other party's failure to fulfill its responsibilities under these terms and conditions. In no event will either party be liable for any lost profits, lost savings, incidental damage, or other economic consequential damages. All expressed and implied warranties, including the implied warranties of merchantability and fitness for a particular purpose, are limited in duration to the coverage period. No warranties, expressed or implied, will apply after this period. BendPak may modify these terms and conditions at any time by either providing the customer with written notice or posting such revised terms on www.bendpak.com. Such revised terms shall be effective thirty days from the date of such written notice or posting.
|
|
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
Features
- 9,000-lb. maximum lifting capacity
- Multi-caster slip plates
- Dual radius plate positions
- heavy-duty stainless steel lifting cables
- Dual-hub cable sheaves
- Grease nipples on every sheave and sheave axle
- Single hydraulic cylinder
- Integrated hydraulic flow restrictor
- Durable powder coat finish
- Spring-loaded safety locks
- Simple push-button lock release
- Aircraft-quality stainless steel and aluminum pneumatic cylinders
- Secondary lock system
- Fully enclosed cables, airlines, safety latches and sheaves
- Multiple adjustable height locking positions
- Maintenance-free power system
- Easy-to-reach operator controls
- Non-skid runways
|
|
 |
 |
 |
 |
|
 |

|