Atlas® Garage Pro 9000 Service/Parking 4 Post Lift Combo 2

Extra Tall - Extra Wide Lift

To View Atlas 4 Post Cylinder Bleeding Procedure Click Here
(Do this immediately after installation)

This Atlas® Garage Pro 9000 4 post lift can accommodate a 187" vehicle. The Atlas® Garage Pro 9000 has the longest runways (we believe) of any portable 9,000 LB. four post on the market. The Atlas® Garage Pro 9000 weighs about 300 LB. more than our Atlas® Garage Pro 8000. The Atlas® Garage Pro 9000 four post above ground lift incorporates many features that are not found in any of our competitors' four post lifts that are sold in the USA. This lift is a portable four post lift incorporating polyurethane casters on the caster kit to prevent damage to the garage floor.

The Garage Pro 9000 can lift your pick-up truck or car up to 85 inches in the air. This above ground lift is the perfect choice for parking taller vehicles under your stored vehicle. The commercial grade features of the Garage Pro 9000 make this lift the perfect choice for automotive service center or Mr. Homeowner that needs a PORTABLE professional four post lift at a competitive price.

Supersedes ATPK-RJ6BK-AH-KIT

The Atlas® ATTD-RJ6BK RJ-6000 (Air/Hydraulic) is a heavy duty rolling jack designed to lift and support 6,000 LB. The commercial grade RJ-6000 (Air/Hydraulic) rolling jack can be used to raise the front or rear portion of a vehicle; allowing the operator of a four post above ground lift to perform wheel and brake service. Most commercial shops buy two of these hydraulic rolling jacks, so that the entire vehicle can be supported in the air at the same time.

The Atlas® RJ-6000 (Air/Hydraulic) has telescoping arms that can be extended over the runways of the four post lift. The lift pads at the end of these arms can be positioned under the LIFTING POINTS that are located over the runways of the four post lift. The Atlas® RJ-6000 (Air/Hydraulic) rolling bridge is equipped with expandable supports which adjust to fit many different brands of four post above ground lifts. These supports have a unique roller system that allows the rolling hydraulic jack to glide easily under the entire length of the vehicle. The large heavy steel wheels allow the rolling jack to be positioned under the correct lifting points in a matter of seconds.

The Atlas® RJ-6000 (Air/Hydraulic) comes standard with a set of peg style truck adapters which increases the lifting height of the lift pads. These truck adapters will allow the Atlas® RJ-6000 rolling hydraulic jack to raise most pick up and larger trucks that will sit higher than the average passenger car.

The Atlas® RJ-6000 (Air/Hydraulic) is equipped with an air/hydraulic pump. The air/hydraulic pump requires a supply of compressed air (air compressor) to work properly.

Important: The Atlas® RJ-6000 is designed and engineered to operate on "delivered" air pressure of between 70-95 PSI. If you exceed 95 PSI, you may damage your jack. For more information on the recommended operating air pressure of the Atlas® RJ-6000 Click Here. The Atlas® RJ-6000 (Air/Hydraulic) rolling hydraulic jack features two solid locking positions that are used when the vehicle is to be suspended above the runways. When the locking positions of the Atlas® RJ-6000 (Air/Hydraulic) are engaged, the hydraulic pressure from the lifting cylinder of the jack is eliminated. (These locks act much like a pair of jack stands after you lift a vehicle off the ground with a service jack).

The Atlas® RJ-6000 (Air/Hydraulic) rolling hydraulic jack features two solid locking positions that are used when the vehicle is to be suspended above the runways. When the locking positions of the Atlas® RJ-6000 (Air/Hydraulic) are engaged, the hydraulic pressure from the lifting cylinder of the jack is eliminated. (These locks act much like a pair of jack stands after you lift a vehicle off the ground with a service jack).