 |
 |
 |
|
BendPak HD-973PX 9,000 & 7,000 Lb. Capacity Tri-Level Parking Lift - Extended / High Lift
The Longer, Higher Triple Decker
The tri-level HD-973PX is a four-post parking lift that maximizes your parking capacity without adding any additional real estate. Each HD-973PX houses up to three vehicles on strengthened parking platforms to give you the most space for your buck. With an additional 84” of overall height compared to the HD-973P parking lift, the HD-973PX supports some of the biggest vehicles around! This extra height, along with the additional 10” of runway length, gives you the perfect amount of space to fit longer and taller vehicles, while maintaining a height that will fit comfortably in most shops and garages. With the topmost platform’s weight capacity sitting at a hefty 7,000 lbs. and the lower deck handling up to 9,000 lbs., the HD-973PX is ideal for lifting even heavy-duty vehicles like full-size trucks and SUVs.
This rugged design is ready for installation indoors or outdoors, instantly tripling your parking and storing
capability. The easy to use top-of-the-line design ensures that your vehicles are being lifted safely, and efficiently. Which saves you time, and worry. The safety features that come standard with any BendPak lift make sure your cars stay in the air until YOU move them, and intuitive design cycles through the cars at the push of a button. With the HD-973PX you’re getting a lift that can not only park your taller and longer vehicles, but fits comfortably and safely wherever you need it most.
Proprietary Design
Shortened height columns allow this car lift to fit in low ceiling spaces where others systems can’t. Although shorter in stature than most tri-level systems, the lower space still yields a full 70 inches of rise.
Independent Platforms
Typical multi-level car stackers include a bottom platform that is suspended from the upper platform via chains or
cables—both platforms move simultaneously. This tethered operation results in limited spacing options between platforms, as the distance between platforms is fixed.
The HD-973PX features independently operated lifting platforms, permitting varied vehicle heights and spacing in either upper or lower parking spaces. Because the platforms do not have to move in unison with one another, you can now lower the bottom platform without disrupting the overhead vehicle being stored. This allows operators to control one platform at a time. Practically speaking, if you only want to swap out the second-level vehicle, you don't have to lower the top-level vehicle.
Unmatched Protection
The patent-pending design of the HD-973PX features multi-position safety locks that are spaced just four inches apart. This allows almost unlimited parking height arrangements on either the upper or lower decks. Redundant, anti-fall, spring-loaded safety catches immediately halt downward movement of either platform in the unlikely event of cable failure.
Hydraulic Power
A powerful hydraulic cylinder is enclosed underside each platform set and is matched with high-strength lifting cables for simplicity and dependability. The lift can be configured for drive-thru operation, allowing as many as three deep for maximum efficiency and better use of space.
Smarter construction means less cost to you
High-rise parking lifts that can fit three vehicles will inevitably cost more than other lifts. There's simply more
steel involved, and larger lifts require additional engineering, all of which gets incorporated in the cost. The HD-973PX offsets much of that extra cost because its smart design requires less steel. The end result is an incredibly efficient parking lift that actually saves buyers thousands of dollars while upholding the industry's most rigid safety standards.
Weight-Displacing Base
Specially designed base frames distribute the load, which makes this unique lifting system suitable for installation on virtually any residential or commercial concrete floor. It can even be installed on asphalt when equipped with concrete footers. The HD-973PX may be configured as a stand-alone lift or combined into rows of multiple units.
Who Should Get This Parking Lift?
Explore the HD-973PX if you need to stack three vehicles in a tight space, or if you want the versatility to vary the parking heights of your second and third-level vehicles. The lift's small footprint and exemplary design makes for an ideal lifting solution in both professional shops and home garages.
|
Specifications
|
HD-973P
|
HD-973PX
|
|
Style
|
Multi-Level Parking Lift
|
Extended Multi-Level Parking Lift
|
|
Top Platform
|
|
Lifting Capacity*
|
7,000 lbs. (3,175 kg)
|
|
*Max Capacity / Front Axle
|
3,500 lbs. (1,588 kg)
|
|
*Max Capacity / Rear Axle
|
3,500 lbs. (1,588 kg)
|
|
A - Overall Width
|
110.5" (2,807 mm)
|
110" (2,807 mm)
|
|
B - Overall Length
|
242" (6,141 mm)
|
252.25" (6,409 mm)
|
|
C - Height of Columns
|
157.75" (4,007 mm)
|
169.75" (4,312 mm)
|
|
D - Drive-thru Clearance
|
86.5" (2,197 mm)
|
|
E - Maximum Rise
|
139.5" (3,544 mm)
|
151.5" (3,849 mm)
|
|
F - Maximum Lifting Height
|
144" (3,667 mm)
|
156.5" (3,972 mm)
|
|
G - Distance Between Columns
|
100" (2,546 mm)
|
|
H - Runway Width
|
19" (482 mm)
|
|
I - Width Between Runways
|
44" (1,121 mm)
|
|
J - Runway Length
|
188.5" (4,786 mm)
|
208.5" (5,296 mm)
|
|
Min. Wheelbase @ rated Capacity
1
|
135" (3,429 mm)
|
140" (3,556 mm)
|
|
Min. Wheelbase @ 75% Capacity
1
|
115" (2,921 mm)
|
120" (3,084 mm)
|
|
Min. Wheelbase @ 50% Capacity
1
|
95" (2,413 mm)
|
100" (2,540 mm)
|
|
Min. Wheelbase @ 25% Capacity
1
|
75" (1,905 mm)
|
80" (2,032 mm)
|
|
Locking Positions
|
31
|
34
|
|
Locking Spacing
|
Every 4" (102 mm)
|
|
Lifting Time to Max. Rise
|
90 seconds
|
|
Motor
|
220 VAC / 60 Hz / 1 Ph
|
|
Bottom Platform
|
|
Lifting Capacity*
|
9,000 lbs. (4,082 kg)
|
|
*Max Capacity / Front Axle
|
4,500 lbs. (2,041 kg)
|
|
*Max Capacity / Rear Axle
|
4,500 lbs. (2,041 kg)
|
|
A - Overall Width
|
112" (2,833 mm)
|
110.5" (2,807 mm)
|
|
B - Overall Length
|
242" (6,139 mm)
|
252.25" (6,409 mm)
|
|
C - Height of Columns
|
161" (4,093 mm)
|
169.75" (4,312 mm)
|
|
D - Drive-thru Clearance
|
90.25" (2,292 mm)
|
86.5" (2,197 mm)
|
|
E - Maximum Rise
|
70" (1,783 mm)
|
82" (2,197 mm)
|
|
F - Maximum Lifting Height
|
75" (1,906 mm)
|
87" (2,197 mm)
|
|
G - Distance Between Columns
|
100" (2,546 mm)
|
|
H - Runway Width
|
19" (482 mm)
|
|
I - Width Between Runways
|
44" (1,121 mm)
|
35" (889 mm) or 41" (1,041 mm)
|
|
J - Runway Length
|
176" (4,470 mm)
|
208.5" (5,296 mm)
|
|
Min. Wheelbase @ rated Capacity
1
|
125" (3,175 mm)
|
135" (3,429 mm)
|
|
Min. Wheelbase @ 75% Capacity
1
|
110" (2,794 mm)
|
115" (2,921 mm)
|
|
Min. Wheelbase @ 50% Capacity
1
|
90" (2,289 mm)
|
95" (2,413 mm)
|
|
Min. Wheelbase @ 25% Capacity
1
|
75" (1,905 mm)
|
75" (1,905 mm)
|
|
Locking Positions
|
13
|
16
|
|
Locking Spacing
|
Every 4" (102 mm)
|
|
Lifting Time to Max. Rise
|
50 seconds
|
|
Motor
|
220 VAC / 60 Hz / 1 Ph
|
|
Shipping Weight
|
|
Shipping Weight
|
5,296-lbs (2,402 kgs)
|
1The Lift supports less weight than its rated capacity when the vehicle’s wheelbase is shorter; this is because the wheels of such a vehicle are closer to the middle of the Runways, where there is less strength. For example, the maximum weight allowed on the Lift for a vehicle with a wheelbase of 95" is 50 percent of the Lift’s rated capacity (or 3,500 lbs. when the rated capacity is 7,000 lbs.).
Note: An air supply (minimum: 30 psi / 3 CFM) is may be required for the safety-lock mechanisms to disengage. It is solely the responsibility of the end-user to provide, install and maintain the air supply.
*Not all BendPak lift models meet the standards as prescribed by ANSI/ALI ALCTV (Current Edition) or ANSI/UL 201. Consult
www.autolift.org for a complete list.
BendPak lifts are supplied with concrete fasteners that meet the criteria of the American National Standard ANSI/ALI ALCTV-(Current). Buyer is responsible for all charges relating to any special regional structural or seismic anchoring requirements specified by any other agencies or codes such as the Uniform Building Code (UBC) or International Building Code (IBC).
Click on Image to Enlarge or Download it
COMMERCIAL PARKING LIFT LIMITED WARRANTY
Better Products – Better Service – Better Value
LIMITED WARRANTY. Subject to the limitations of set forth below, Warrantor warrants that the Product sold hereunder conform to Warrantor's
published specifications. WARRANTOR MAKES NO REPRESENTATION OR WARRANTY OF ANY OTHER KIND, EXPRESS OR IMPLIED, WITH RESPECT TO
THE GOODS, WHETHER AS TO MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER MATTER
Duration:
From the date of purchase by the original Purchaser or 60-24-12 months from the date of shipment by BendPak or whichever comes first.
- Two Years (24-Months) Warranty on the lift structure
- One Year (12-Months) Warranty on the hydraulic cylinder(s) and power unit
- One Year (12-Months) Warranty on operating components
- One Year (12-Months) Warranty on electrical components (excluding power unit)
- One Year (12-Months) Labor Warranty on site or at factory*
- One Year (12-Months) Free-Shipping** on ground-freight charges related to warranty performance
Limited Warranty
- Who gives this warranty (Warrantor): BendPak Inc., 1645 lemonwood dr. Santa Paula, CA 93060
- Who receives this warranty (Purchaser): The original Purchaser (other than for purpose of resale)
- What products are covered by this warranty: Any BendPak Two-Post or Four-Post car lift**
- What is covered under this warranty: manufacturer defects due to material and/or workmanship with the exceptions noted below.
- What is not covered under this warranty:
- Any failure that results from Purchaser’s abuse, neglect or failure to operate, maintain or service product in accordance with instructions provided in the owner’s manual(s) supplied
- And damage caused by overloading lift beyond rated capacity
- Items or service normally required to maintain the product, i.e. lubricants, oil, etc.
- Items considered general wear parts such as rubber pads, lifting cables, etc. unless wear or failure is a direct result of manufacturer defect due to material and/or workmanship
- Any component damaged in shipment or any failure caused by installing or operating lift under conditions not in accordance with installation and operation guidelines or damaged by contact with tools or surroundings
- Motor or pump failure caused by rain, excessive humidity, corrosive environments or other contaminants
- Rusted components due to improper maintenance or corrosive environments
- Cosmetic defects that do not interfere with product functionality
- Damage due to incorrect voltage or improper wiring
- Any incidental, indirect, or consequential loss, damage, or expense that may result from any defect, failure, or malfunction of BendPak Inc product
- Responsibilities of Warrantor under this warranty: Repair or replace, at Warrantor’s option, component which is defective, has malfunctioned and/or failed to conform within duration of the warranty period. BendPak Inc. will pay reasonable labor costs for the first 12 months only
- Responsibilities of Purchaser under this warranty:
- Provide dated proof of purchase and maintenance records
- In some cases, components may be required to be shipped to the nearest BendPak Authorized Service Center. Freight costs, after 12-months, must be borne by the Purchaser.
- Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).
- When Warrantor will perform repair or replacement under this warranty: Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts.
*Free-shipping applies to direct shipping points within the 48 continental United States. Rural area shipping surcharge may apply for remote addresses. **For all BendPak brand two-post and four-post surface mounted lifts manufactured on or following 1/1/2011.
Limitation of Liability
In no event will either party be liable for any damage caused by the other party's failure to fulfill its responsibilities under these terms and conditions. In no event will either party be liable for any lost profits, lost savings, incidental damage, or other economic consequential damages. All expressed and implied warranties, including the implied warranties of merchantability and fitness for a particular purpose, are limited in duration to the coverage period. No warranties, expressed or implied, will apply after this period. BendPak may modify these terms and conditions at any time by either providing the customer with written notice or posting such revised terms on www.bendpak.com. Such revised terms shall be effective thirty days from the date of such written notice or posting.
https://bendpakcs.freshdesk.com/a/tickets/new
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features
- Extended length, high rise
- Perfect for parking, storage and service
- 7,000 lb. capacity upper deck
- 9,000 lb. capacity lower deck
- Superstructure features durable powder coat finish
- Perfect for cars, trucks, and SUVs
- Platforms feature full-length aluminum decking
- Rugged welded-steel construction
- Powerful hydraulic cylinders
- Heavy-duty 3/8” lifting cable
- Heavy-duty steel construction
- Wide base-plate for maximum stability
- Heavy-duty steel construction
- Grease nipples are located on every sheave and sheave axle to make lubrication maintenance a breeze
- Integrated hydraulic flow restrictor provides controlled descent in event of hose rupture
- Reliable electric-hydraulic power system
- Runways feature non-skid surface
- Multi-position safety locks in each column
- Automatic safety locks combined with redundant anti-fall devices
- Adjustable lock ladders
- Independent backup slack-cable safety latches
- Push-button pneumatic safety release.
- Padded trip bar with limit switch prevents lower vehicle from making contact with upper platform.
- Simple controls
- Optional drive-thru ramps available
- Optional 4,500-lb. air-hydraulic rolling jacks available
|
|
|
|
|
|
| Accessories for this product... |
|
|
|
|
Owned & Operated in the U.S. since 1987
