 |
 |
 |
|
BendPak XR-12000L Quatra™ Pantograph Scissors Lift 12,000 lb
To View or download the lift inspection guide
Click Here.
BendPak's Quatra is one of those once-in-a-generation shop lifts that saves space and increases lift capacity. For such a compact size, it’s amazing that it breezily achieves 12,000 lbs. of lift.
Reliable Balance & Mechanical Locking
The Quatra features zero radial shift, which is basically unheard of for a car lift that raises vehicles up to 12,000 lbs. Whereas parallelogram lifts need at least a little extra floor space to accommodate their lateral shift, the Quatra goes straight up-and-down. Additionally, the XR-12000L is equipped with an intelligent hydraulic regulating manifold. This device has four, two-position ball valves that create a balance of hydraulic pressure between the master and slave cylinders. This mission-critical system guarantees a level rise and descent at all times. Not only that, each ball valve is part of a mechanical lock system that lets you leave the Quatra raised indefinitely. The manifold valve assembly is found right on the power console. It also features a cover that can be removed for maintenance and other adjustments.
One-of-a-kind Design
The Quatra benefits from an ergonomic design that helps operators raise and lower quickly and safely. The increase in productivity is obvious from the first time you lift a vehicle. The ability to get underneath a raised lift from any angle is unique for a scissor lift (although the Quatra is not a true scissor lift). The lift rises and descends rapidly to your preferred height with just the push of a button.
It’s All in the Approach
When it comes to positioning vehicles on a car lift, there is no other model on the market that makes it easier. The approach ramps have a wide range of extension, from 56” all the way up to an incredible 79”. Extend them in just seconds flat. These ramps are favorites of our customers, especially when there isn’t much space to work with but a lot of work to get done. In short, the Quatra series lift by BendPak is the solution for customers who want one of the industry’s most versatile and comprehensive car lift models.
Optional Equipment Available
Optional 6,000-lb. capacity rolling jacks (model RBJ6000) make a great addition to increase service capacity. Each jack has telescoping arms and frame contact pads that can be extended over the runways and positioned under vehicle lifting points. Each jack features three safety‐lock positions and stackable truck and van adapters for increased lifting height and better access to frame contact points on high ground‐clearance vehicles. The jacks come equipped with a commercial grade air‐hydraulic pump requiring a maximum pressure of 125 psi and 10‐20 CFM./p>
An optional integrated rolling bridge airline kit is available that installs neatly within the runway to create a more tidy hose-routing solution for single or dual jack purpose.
|
Model
|
XR-12000L
|
|
Capacity
|
|
Lifting Capacity: (*)
|
12,000 lbs. (5,443 kg)
|
|
Rise
|
|
A - Min. Runway Height
|
11.75” (298 mm)
|
|
B - Max. Lifting Height
|
75" (1,910 mm)
|
|
Outside Dimensions
|
|
C - Overall Width
|
88" (2,184 mm)
|
|
D - Length / Ramps Extended
|
276.75" (7,029 mm)
|
|
D - Length / Ramps Collapsed
|
257.75" (6,547 mm)
|
|
D - Length / Ramps Stowed
|
225" (5,715 mm)
|
|
Runways
|
|
E - Runway Width
|
24" (610 mm)
|
|
F - Width Between Runways
|
40" (1,028 mm)
|
|
G - Length of Runways
|
193" (4,902 mm)
|
|
Minimum Wheelbase
|
|
H - General Service Wheelbase
|
175.5" (4,458 mm)
|
|
Rated Capacity
|
135" (3,429 mm)
|
|
75% Capacity
|
120" (3,048 mm)
|
|
50% Capacity
|
100" (2,540 mm)
|
|
25% Capacity
|
80" (2,032 mm)
|
|
Locking
|
|
Locking Positions
|
13
|
|
Power Unit
|
|
Motor
|
220 VAC / 60 Hz / 1 Ph
|
|
Noise
|
45 dB
|
|
Shipping
|
|
Dimensions
|
197" x 25" x 36" (5,003 mm x 635 mm x 914 mm)
|
|
Weight
|
4,793-lbs. (2,174 kg)
|
Note - An air supply (minimum: 30 psi / 3 CFM) is required for the safety-lock mechanisms to disengage. It is solely the responsibility of the end-user to provide, install and maintain the air supply.
Note - Not all BendPak lift models meet the standards as prescribed by ANSI/ALI ALCTV-2006 or ANSI/UL 201. Consult
www.autolift.org for a complete list.
Click on Image to Enlarge or Download It
FULL-RISE SCISSOR LIFTS WARRANTY
Duration: From the date of purchase by the original Purchaser or 12-24 months from the date of shipment by BendPak or whichever comes first.
- Two Years (24-Months) Warranty on the lift structure
- One Year (12-Months) Warranty on the hydraulic cylinder(s) and power unit
- One Year (12-Months) Warranty on operating components
- One Year (12-Months) Labor Warranty on site or at factory
- One Year (12-Months) Free-Shipping* on ground-freight charges related to warranty performance
Limited Warranty
1. Who gives this warranty (Warrantor): BendPak Inc., 1645 Lemonwood Dr., Santa Paula, CA 93060
2. Who receives this warranty (Purchaser): The original Purchaser (other than for purpose of resale)
3. What products are covered by this warranty: Any BendPak Full-Rise Scissor Lift**
4. What is covered under this warranty: manufacturer defects due to material and/or workmanship with the exceptions noted below.
5. What is not covered under this warranty:
a. Any failure that results from Purchaser’s abuse, neglect or failure to operate, maintain or service product in accordance with instructions provided in the owner’s manual(s) supplied
b. Any damage caused by overloading lift beyond rated capacity
c. Items or service normally required to maintain the product, i.e. lubricants, oil, etc.
d. Items considered general wear parts such as rubber pads, pad adapters, etc. unless wear or failure is a direct result of manufacturer defect due to material and/or workmanship
e. Any component damaged in shipment or any failure caused by installing or operating lift under conditions not in accordance with installation and operation guidelines or damaged by contact with tools or surroundings
f. Motor or pump failure caused by rain, excessive humidity, corrosive environments or other contaminants
g. Rusted components due to improper maintenance or corrosive environments
h. Cosmetic defects that do not interfere with product functionality
i. Damage due to incorrect voltage or improper wiring
j. Any incidental, indirect, or consequential loss, damage, or expense that may result from any defect, failure, or malfunction of BendPak Inc. product
k. All electrical components are guaranteed for one year against defects in workmanship and/or materials when the lift is installed and used according to specifications.
6. Responsibilities of Warrantor under this warranty: Repair or replace, at Warrantor’s option, component which is defective, has malfunctioned and/or failed to conform within duration of the warranty period. BendPak Inc. will pay reasonable labor costs for the first 12 months only
7. Responsibilities of Purchaser under this warranty:
a. Provide dated proof of purchase and maintenance records
b. In some cases, components may be required to be shipped to the nearest BendPak Authorized Service Center. Freight costs, after 12-months, must be borne by the Purchaser.
c. Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).
8. When Warrantor will perform repair or replacement under this warranty: Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts.
*Free-shipping applies to direct shipping points within the 48 continental United States. Rural area shipping surcharge may apply for remote
addresses.
**For all BendPak brand Full-Rise Scissor Lifts (excluding specialty lifts, material handling, or models for particular
purpose manufactured on or following 8/1/2012.
Limitation of Liability
BendPak/Ranger shall have no obligation pursuant to this Warranty with respect to products which in our sole judgment have been altered
damaged, misused, abused, badly worn, lost or improperly maintained. This Warranty is null and void if the customer or any other person other
than an authorized representative of BendPak/Ranger has made any attempt to service or modify the tool prior to its return to BendPak/Ranger
under this Warranty. In no event will either party be liable for any damage caused by the other party's failure to fulfill its responsibilities under
these terms and conditions. In no event will either party be liable for any lost profits, lost savings, incidental damage, or other economic
consequential damages. All expressed and implied warranties, including the implied warranties of merchantability and fitness for a particular
purpose, are limited in duration to the coverage period. No warranties, expressed or implied, will apply after this period. BendPak may modify
these terms and conditions at any time by either providing the customer with written notice or posting such revised terms on
www.bendpak.com. Such revised terms shall be effective thirty days from the date of such written notice or posting.
https://bendpakcs.freshdesk.com/a/tickets/new
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features
- 12,000-lb. lifting capacity
- Durable powder-coat finish that can withstand harsh environments and chemical spills and will provide years of protection
- Extendable, hinged, collapsible, and stowable approach ramps
- Multi‐position runway work steps
- Non‐skid runways provide sure grip for vehicles and technicians
- Dependable electric/hydraulic power system
- Cylinders feature integrated velocity fuses to control sudden descent
- Power console features simple operator controls
- Open front design with clear center, sides and rear
- Multi‐position automatic leveling system
- Quad automatic safety locks with pneumatic push‐button release
- Collapsible front tire stops clear for low vehicle skirts
- Lubricated‐for‐life bearings on all pivot points
- Rugged steel legs and formed steel runways
- Turned, ground, polished and hardened zinc plated axle pins
- Grease nipples on all moving pins and bearings
- High efficiency hydraulic power unit provides faster raising and descent times
- Easy access to hydraulic-electrical components for simple routine servicing
- Easy to use and understand operator controls
- Power unit console with easy access front panel
- Can be surface or flush-mounted
|
|
|
|
|
|
| Accessories for this product... |
|
|
|
|
Owned & Operated in the U.S. since 1987
