 |
 |
 |
 |
BendPak PL-6KDT Tandem / Independent Platforms Parking Lift 12,000-lb. Cap.
The PL-6KDT is an indoor-outdoor platform car lift that holds a total of four vehicles in its 224” x 205” x 124” frame. Dual hydraulic cylinders and a pair of stabilizing lifting cables support two lifting platforms. The cables are routed internally throughout the parking lift.
This lift is intended for use by anyone with four vehicles but only one wide garage area to store them. You’ll be surprised to see how well this unit fits in a variety of garage sizes. In the right space, it can be successfully utilized for either commercial or residential purposes.
Choose extended-width
For wide-clearance vehicles, we’ve extended the columns of the PL-6KDTX car lift a little wider. This ensures that truck mirrors gracefully pass through the lift structure, and vehicle doors have a little more room to open and close. Some folks find the extra space more accommodating when they need to access the vehicle.
One lift houses four vehicles
For many car enthusiasts, municipal parking lots and professional shops with limited parking space, the only way to park vehicles has been to buy multiple parking lifts and place them side-by-side, as close together as possible. This not only takes up an obscene amount of space, it’s expensive to keep buying more lifts. The PL-6KDT will hold most vehicles up to 6,000 lbs., and because it doesn’t have any posts between the two lifting platforms, you can fit this double-wide parking lift in most two-door garages.
Two independent platforms
Two full-width, high-strength galvanized steel platforms cover most of the length of the parking lift. No in-between columns take up extra space, so your parking lift offers maximum lifting ability with a minimal footprint. Because each platform is independently suspended by taut, aircraft-quality steel cables, one vehicle can be lowered while the other side remains still. This eliminates the need to “shuffle” vehicles from the half of the lift where vehicles are not being accessed.
Internally routed hydraulic lines and cables
When the parking lift platform reaches its max height, the lock system automatically engages, safely and indefinitely suspending your vehicle out of harm’s way.
Single-position, auto-engaging lock
When the puzzle lift platform reaches its max height, the lock system automatically engages, safely and indefinitely suspending your vehicle out of harm’s way.
Park safer inside
Vehicle parking lifts offer a safer alternative to parking multiple cars in the driveway or street. Rather than being forced to park your precious cargo outdoors where it gets exposed to weather, accidents and theft, keep your cars, trucks and/or SUVs safely tucked inside. There’s no price tag on your peace of mind.
Power options
This parking lift can be configured for 110V or 220V operation. International voltages available.
GoPro Time Lapse of BendPak Home Garage Lift Installation
BendPak Home Garage Car Lift Installation
Specifications
|
PL-6KDT
|
PL-6KDTX
|
PL-6KT
|
Style
|
Style
|
Multi-Platform
|
Ex-Wide Multi-Platform
|
Triple Multi-Platform
|
Capacity
|
Lifting Capacity
|
6,000-lb. Per Deck (12,000 lbs. total) / 2,722 kg
|
Overall Width
|
210.75” (5,353 mm)
|
250” / 6,350 mm
|
308” (7,834 mm)
|
Overall Length
|
236-1/2” / 6,008 mm
|
Overall Height
|
122.75” (3,118 mm)
|
123.75” (3,140 mm)
|
Min. Runway Height
|
9” / 230 mm
|
Max. Rise
|
89” / 2,261 mm
|
Width Between Posts
|
185-1/2" / 4,715 mm
|
225” / 5,713 mm
|
283" (7,197 mm)
|
Platform Width
|
82" / 2,086 mm
|
Length of Platforms
|
152" / 3,862 mm
|
Drive-thru Clearance
|
93" / 2,374 mm
|
Locking Positions
|
1 (Adjustable)
|
Lifting Time
|
30 Seconds
|
Standard Motor
|
220 VAC / 60 Hz. 1Ph.
|
Shipping
|
Shipping Weight
|
6,905-lbs. (3,132 kg)
|
7,125-lbs. (3231 kg)
|
8,889-lbs. (4,032 kg)
|
Shipping Dimensions
|
234" x 32" x 62" (5,943 x 812 x 1,574 mm)
|
310" x 32" x 63" (7,874 x 813 x 1,600 mm)
|
*Not all BendPak lift models meet the standards as prescribed by ANSI/ALI ALCTV-2006 or ANSI/UL 201. Consult
www.autolift.org for a complete list.
Better Products – Better Service – Better Value
LIMITED WARRANTY. Subject to the limitations of set forth below, Warrantor warrants that the Product sold hereunder conform to Warrantor's
published specifications. WARRANTOR MAKES NO REPRESENTATION OR WARRANTY OF ANY OTHER KIND, EXPRESS OR IMPLIED, WITH RESPECT TO
THE GOODS, WHETHER AS TO MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER MATTER
Duration: From the date of purchase by the original Purchaser or 60-24-12 months from the date of shipment by BendPak or whichever comes first.
- Five Years (60-Months) Warranty on the lift structure
- Two Years (24-Months) Warranty on the hydraulic cylinder(s) and power unit
- One Year (12-Months) Warranty on operating components
- One Year (12-Months) Warranty on electrical components (excluding power unit)
- One Year (12-Months) Labor Warranty on site or at factory*
- One Year (12-Months) Free-Shipping** on ground-freight charges related to warranty performance
Limited Warranty
- Who gives this warranty (Warrantor): BendPak Inc., 1645 lemonwood dr. Santa Paula, CA 93060
- Who receives this warranty (Purchaser): The original Purchaser (other than for purpose of resale)
- What products are covered by this warranty: Any BendPak Two-Post or Four-Post car lift***
- What is covered under this warranty: manufacturer defects due to material and/or workmanship with the exceptions noted below.
- What is not covered under this warranty:
- Any failure that results from Purchaser’s abuse, neglect or failure to operate, maintain or service product in accordance with instructions provided in the owner’s manual(s) supplied
- Any damage caused by overloading Product beyond rated capacity
- Items or service normally required to maintain the product, i.e. lubricants, oil, etc.
- Items considered general wear parts such as rubber pads, lifting cables, etc. unless wear or failure is a direct result of manufacturer defect due to material and/or workmanship
- Any component damaged in shipment or any failure caused by installing or operating lift under conditions not in accordance with installation and operation guidelines or damaged by contact with tools or surroundings
- Motor or pump failure caused by rain, excessive humidity, corrosive environments or other contaminants
- Rusted components due to improper maintenance or corrosive environments
- Cosmetic defects that do not interfere with product functionality
- Damage due to incorrect voltage or improper wiring
- Any failure that results from improper installation or use not according to specifications
- Damage caused by disasters such as fire, flood, wind, and lightning
- Damage caused by unauthorized attachments or modifications
- Responsibilities of Warrantor under this warranty: Repair or replace, at Warrantor’s option, component which is defective, has malfunctioned and/or failed to conform within duration of the warranty period. BendPak Inc. will pay reasonable labor costs for the first 12 months only
- Responsibilities of Purchaser under this warranty:
- Provide dated proof of purchase and maintenance records
- In some cases, components may be required to be shipped to the nearest BendPak Authorized Service Center. Freight costs, after 12-months, must be borne by the Purchaser.
- Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).
- Immediately upon receipt of the Product, Purchaser shall inspect the same. Any claim for shortage must be made within ten days after Purchaser's receipt. All other claims, including claims for alleged defective Product, must be made within fifteen days after Purchaser learns of the facts upon which such claim is based, but in no event later than the applicable one, two or five year period specified above for the specified component(s). All claims not made in writing and received by Seller within the time periods specified above shall be deemed waived. With respect to any defects incapable of discovery until in use, all claims for any
damages or losses as a result of such defects shall be deemed waived unless made in writing and received by Seller within fifteen days after Purchaser learns of the alleged defect giving rise to the claim and after the expiration of said periods, but in no event later than the applicable one, two or five year period specified above for the specified component(s). Purchaser expressly assumes all liability for all such damages or losses, irrespective of any use which shall have taken place or whether the alleged defect shall have occurred or been discovered prior to expiration of such periods.
- When Warrantor will perform repair or replacement under this warranty: Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts.
*As determined by Warrantor in its sole discretion**Free-shipping applies to direct shipping points within the 48 continental United States.
Rural area shipping surcharge may apply for remote addresses. ***For all BendPak brand Two-Post or Four-Post Vehicle Service Lifts
(excluding specialty lifts, high rise, commercial parking, material handling, or models for particular purpose) manufactured on or following
1/1/2011.
https://bendpakcs.freshdesk.com/a/tickets/new
|
|
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
Features
- 6,000-lb. Capacity Per Deck (12,000 lbs. total)
- Perfect for cars, light trucks, motorcycles and ATVs
- Rugged I-beam and C-channel construction
- Built-in wheel stops
- Wide base-plate for maximum stability
- Front and rear wheel chocks
- Superstructure features durable powder-coat finish
- Dual hydraulic cylinders with heavy-duty steel lifting cable
- Heavy-duty steel construction
- Reliable electric-hydraulic power system
- Full-width platform to keep bottom vehicles protected
- Simple controls
- Oversized sheave diameter reduces cable fatigue
- High-speed lifting
- Features heavy-duty 3/8" aircraft cable
- Rugged 1-1/4" roller axles
- Multi-position safety locks in each column
- Push-button pneumatic safety release
- Independent backup slack-cable safety latches
- Customizable power unit location
This is a Special Order Item has a 90 - 120 Day Lead-time. There is 50% NON REFUNDABLE Charge
|
|
 |
 |
 |
 |

|