 |
 |
 |
|
HDSO-14LAX-Combo Includes:
BendPak HDSO-14AX 4 Post Alignment Rack
To view the lift inspection guide
Click Here
We engineered our HDSO-14AX model without a front cross bar, so operators can easily enter and exit from beneath the vehicle. Now the process of front-end adjustment becomes quick and trouble-free. This is a must for busy alignment bays. Additionally, for precise front-lift leveling, nothing beats our patented adjustable front outrigger tubes. The infinitely adjustable pitch compensates for excessive loads and sloped floors.
Ranger 3DP4100R Target 3DPro™ Imaging Wheel Alignment System
Includes Set-Up & Training
The Target 3DPro increases productivity by allowing technicians to do more alignments in less time compared to conventional systems. The Target 3DPro is perfect for wheel service repair shops handling a high volume of wheel alignments who are looking for dramatic improvements in profitability. With minimal investment and reduced training, the Ranger Target 3DPro aligner expands your service potential and sends more profit to your bottom line. ProSpec® feedback that assists the technician in diagnosing problems all add up to customer satisfaction and improved shop efficiency.
All alignment steps from start-to-finish are clearly shown with vibrant animation and graphics providing a faster, more profitable and far easier to understand alignment procedure. Simplistic read results enable you to also identify potential problem areas specifically related to suspension components.
 The 3DP4100 wheel aligner gives you the option of selecting the most effective measuring routines before starting wheel alignment procedures. Standard option for a program-guided routine with initial and final measurements; rapid procedure for measurements without caster steering angle and/or run-out compensation; or free measurement for checking individual values as required.
BendPak RJ-7 Rolling Bridge Jack (Set of 2)
These optional, 7,000Lb. capacity rolling bridge jacks offer the ultimate in jacking speed and convenience. Their exclusive telescoping roller design allows the runways to be adjusted for different tread widths. Precision rollers enable you to position them anywhere under the vehicle. Perfect for wheel and suspension work. Each jack comes complete with stackable pad adapters and axle support plates.
|
Specifications
|
HDSO-14AX
|
Lifting Capacity*
*Max capacity / front axel:
*Max capacity / rear axel:
|
14,000 lbs. / 6,350 kg
7,000 lbs. / 3,175 kg
7,000 lbs. / 3,175 kg
|
|
A - Overall Front Width
|
143" / 3,632 mm
|
|
A - Overall Rear Width
|
130” / 3,301 mm
|
|
B - Outside Length
|
215" / 5,472 mm
|
|
B - Overall Length
|
243" / 6,191 mm
|
|
D - Height of Front Columns
|
103" / 2,623 mm
|
|
D - Height of Rear Columns
|
92" / 2,338 mm
|
|
E - Min. Runway Height
|
7-5/8" / 192 mm
|
|
F - Max. Rise
|
70" / 1,778 mm
|
|
G - Max. Lifting Height
|
77-5/8" / 1,970 mm
|
|
H - Width Between Front Columns
|
123" / 3,124 mm
|
|
H - Width Between Rear Columns
|
120" / 3046 mm
|
|
I - Runway Width
|
20" / 508 mm
|
|
J - Width Between Runways
|
37-1/2" – 51" / 952 mm – 1,295 mm
|
|
K - Runway Centerline
|
65" / 1651 mm
|
|
L - Outside Edge of Runways
|
85" / 2159 mm
|
|
M - Drive-thru Clearance
|
97" / 2464 mm
|
|
N -Length of Runways
|
199" / 5054 mm
|
|
Min Wheelbase @ Rated Capacity
|
140” / 3,556 mm
|
|
Min Wheelbase @ 75% Capacity
|
120” / 3,048 mm
|
|
Min Wheelbase @ 50%Capacity
|
100” / 2,540 mm
|
|
Min Wheelbase @ 25% Capacity
|
80” / 2,032 mm
|
|
Locking Positions
|
13
|
|
Lock Spacing
|
every 4" / 102 mm
|
|
Lifting Time
|
60 Seconds
|
|
Standard Motor (**)
|
220 VAC / 60 Hz. 1Ph.
|
* May vary depending on wheel size.
** Special Voltages Available Upon Request.
The design, material and specifications are subject to change without notice.
*Not all BendPak lift models meet the standards as prescribed by ANSI/ALI ALCTV-2006 or ANSI/UL 201. Consult
www.autolift.org for a complete list.
Ranger 3DP4100R
- Power Requirements:
- 115V / 1Ph, 50/60 Hz / 8 amp - 230V / 1Ph, 50/60 Hz / 8 amp
BendPak HDSO-14AX
Better Products – Better Service – Better Value
Duration:
From the date of purchase by the original Purchaser or 60-24-12 months from the date of shipment by BendPak or whichever comes first.
a Five Years (60-Months) Bumper-to-Bumper Warranty on the lift structure
a Two Years (24-Months) Warranty on the hydraulic cylinder(s) and power unit
a One Year (12-Months) Labor Warranty on site or at factory
a One Year (12-Months) Free-Shipping* on ground-freight charges related to warranty performance
Limited Warranty
- Who gives this warranty (Warrantor): BendPak Inc., 1645 lemonwood dr. Santa Paula, CA 93060
- Who receives this warranty (Purchaser): The original Purchaser (other than for purpose of resale)
- What products are covered by this warranty: Any BendPak Two-Post or Four-Post car lift**
- What is covered under this warranty: manufacturer defects due to material and/or workmanship with the exceptions noted below.
- What is not covered under this warranty:
- Any failure that results from Purchaser’s abuse, neglect or failure to operate, maintain or service product in accordance with instructions provided in the owner’s manual(s) supplied
- And damage caused by overloading lift beyond rated capacity
- Items or service normally required to maintain the product, i.e. lubricants, oil, etc.
- Items considered general wear parts such as rubber pads, lifting cables, etc. unless wear or failure is a direct result of manufacturer defect due to material and/or workmanship
- Any component damaged in shipment or any failure caused by installing or operating lift under conditions not in accordance with installation and operation guidelines or damaged by contact with tools or surroundings
- Motor or pump failure caused by rain, excessive humidity, corrosive environments or other contaminants
- Rusted components due to improper maintenance or corrosive environments
- Cosmetic defects that do not interfere with product functionality
- Damage due to incorrect voltage or improper wiring
- Any incidental, indirect, or consequential loss, damage, or expense that may result from any defect, failure, or malfunction of BendPak Inc product
- Responsibilities of Warrantor under this warranty: Repair or replace, at Warrantor’s option, component which is defective, has malfunctioned and/or failed to conform within duration of the warranty period. BendPak Inc. will pay reasonable labor costs for the first 12 months only
- Responsibilities of Purchaser under this warranty:
- Provide dated proof of purchase and maintenance records
- In some cases, components may be required to be shipped to the nearest BendPak Authorized Service Center. Freight costs, after 12-months, must be borne by the Purchaser.
- Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).
- When Warrantor will perform repair or replacement under this warranty: Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts.
*Free-shipping applies to direct shipping points within the 48 continental United States. Rural area shipping surcharge may apply for remote addresses. **For all BendPak brand two-post and four-post surface mounted lifts manufactured on or following 1/1/2011.
Limitation of Liability
In no event will either party be liable for any damage caused by the other party's failure to fulfill its responsibilities under these terms and conditions. In no event will either party be liable for any lost profits, lost savings, incidental damage, or other economic consequential damages. All expressed and implied warranties, including the implied warranties of merchantability and fitness for a particular purpose, are limited in duration to the coverage period. No warranties, expressed or implied, will apply after this period. BendPak may modify these terms and conditions at any time by either providing the customer with written notice or posting such revised terms on www.bendpak.com. Such revised terms shall be effective thirty days from the date of such written notice or posting.
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features
BendPak HDSO-14AX
- 14,000 pound lifting capacity
- CE Approved and Certified. Meets or exceeds the standards prescribed by European Standard EN-1493
- Two runway lengths to choose
- Heavy‐duty turn plates and integrated rear slip‐plates included
- Multi‐position turn plate pockets
- Automatic leveling system
- Multiple auto-leveling locking positions
- Runways include rail‐kit for optional accessories
- Electric / hydraulic power system
- Single hydraulic cylinder mounted underneath runway
- Fully enclosed lifting cables, safety locks, and sheaves
- Internal “Anti-Sway” slider blocks in each column
- Features oversize sheaves and heavy‐duty 1/2” aircraft cable
- Rugged 1‐3/8” roller axles and oversize self‐lubricating cable sheaves
- Multi‐position safety locks in each column with push‐button safety release
- Runways adjust for different tread widths and feature non‐skid surface
Ranger 3DP4100R
- Self-balancing, variable height camera lift system is built with precision bearing slides for easy adjustment
- Commercial-grade cameras are designed with full frame optical lenses that ensure accuracy and stability
- High-resolution drive-on approach camera provides full on-screen frontal view of vehicle driving on lift platforms.
- Equipped with an additional large lower flat panel LCD monitor that provides operator with easy-to-read screen views all the way from the rear underside of the vehicle. No need for separate portable hand-held monitors.
- Interactive software provides demonstration screens that assist the technician to easily proceed systematically through the adjustment process
- Rugged checkerboard shockproof wheel targets are drop-tested for worry-free handling and are built with anti corrosion components capable of withstanding harsh working environments.
- German engineered ProSpec® software has been designed to be compatible with Windows 7 and capable of future upgrades.
- In less than 2-minutes, technicians can complete total vehicle set-up (including run-out compensation) and obtain full geometry alignment readings.
- Exclusive One-Touch enhanced software interface results in increased productivity.
- A web based application that can be accessed from iPhone, iPod touch and iPad users to enjoy full wireless remote operation.
- A reduction in the number of vulnerable electric components results in reduced downtime, lower operating costs and a longer service life cycle of the equipment.
- Superior screen graphics with vibrant animation and displays deliver easy to understand visuals and instruction.
- Alignment functions and measurements are controlled via the mouse, keyboard or remote control.
- Self-explanatory graphic user surface provides simple understanding.
- Compatible with low ride-height vehicles or those with ground-effects.
- Self-centering wheel-clamp adaptors cover an extended range of vehicles.
- Cordless design remove hassle of connecting cables.
- Technician has the option to customize alignment units of measure, accuracy, language, etc.
- Technician has a choice of rolling or lifted run-out modes.
- Features self-diagnostic help screen and system information.
- Continuous checking ensures accurate toe measurements.
- On-screen display indicates if sensor leveling is required.
- Vehicle adjustment illustrations and multiple adjustment bar graphs.
- Adjustment illustrations provide illustrated diagrams and instructional information of recommended OEM adjustment methods..
- Valuable customer information can be conveniently stored in the database allowing shop personnel to quickly reference previous alignment work orders.
- Before and after measurements can be printed in full-color to explain service and record work performed.
Standard Equipment
- (1) Target 3DPro variable height camera tower
- (1) Windows® 10 Mini PC Stick - Intel® Atom Quad Core CPU, 2GB RAM, 32GB Memory, Bluetooth 4.0
- Low voltage
- Full-sized, sloped keyboard for easy use. Provides user-friendly control of all alignment procedures.
- (1) Computer mouse
- (1) Console keyboard
- (1) Remote control
- (1) 32” diagonal Upper Flat Panel LCD Monitor designed for complete comfort and convenience with 1280x1024 pixels resolution for sharp and brilliant images of text and graphics. Offers wide viewing angle of 160° horizontal and vertical.
- (1) 19” diagonal Lower Flat Panel LCD Monitor designed for complete comfort and convenience with 1280x1024 pixels resolution for sharp and brilliant images of text and graphics. Offers wide viewing angle of 160° horizontal and vertical.
- (4) 13”-25” wheel clamps
- (1) Target 3DPro variable height camera tower
- (1) Steering wheel lock
- (1) Brake pedal depressor
- Current year domestic and foreign car vehicle specifications
Includes Set-Up & Training
BendPak RJ-7 Set of 2
- 7,000 LBS Automotive Lift with open center.
- Works with BendPak HD-14 series alignment lifts
- Scissor mechanism allows for level lifting
- Weight: 300 lbs
|
|
|
|
|
|
|
Owned & Operated in the U.S. since 1987
