 |
 |
 |
|
BendPak HDS-14XT Extended High-Rise 4 Post Lift 14,000 lb.
To view the lift inspection guide
Click Here.
No Such Thing as Overboard
BendPak's HDS-14 four-post lift is engineered to meet the strenuous demands of your toughest professional lifting applications. Incorporated into every lift is a laundry list of key features as long as your arm, ensuring BendPak lifts remain the absolute best
Extended runways
14,000-lb. vehicles have wheelbases that need specialized equipment to keep them safe and supported. Our extended runways prevent wear and tear on your vehicle; driving onto a car lift runway should not feel like your truck is climbing Mt. Everest.
Dual-hub cable sheaves
Dual-hub cable sheaves reduce stress, fatigue and wear. Huge 10.5” diameter cable sheaves within the runway and cross tubes combine with massive 2.25” diameter sheave axles. This dramatically improves cable wear and critical component lifespan, which means less service-related expenses down the road.
Heavy-duty aircraft cable
This car lift features four, 1/2" diameter, 6 x 25 stainless-steel lifting cables that have a breaking strength of over 14,000 lbs. each. This aircraft-quality cable was specifically designed for lifting applications and provides a great balance between abrasion resistance and fatigue..
Large base plates
10” x 12” base plates provide a solid foundation for every 14K capacity four-post car lift.
Spring-loaded safety locks
Safety locks automatically engage continuously during rise, and adjustable safety ladders allow for precise runway leveling, even when installed on sloped floors.
|
Model
|
HDS-14
|
HDS-14XT
|
|
Style
|
Standard Length
|
Extended Length
|
|
Capacity
|
|
Lifting Capacity: (*)
|
14,000 lbs. (6,350 kg)
|
|
*Max Capacity / Front Axle
|
7,000 lbs. (3,175 kg)
|
|
*Max Capacity / Rear Axle
|
7,000 lbs. (3,175 kg)
|
|
Rise
|
|
A - Min. Runway Height
|
7.5" (191 mm)
|
6.75" (171 mm)
|
|
B - Max. Rise
|
70" (1,778 mm)
|
83" (2,104 mm)
|
|
C - Max. Lifting Height
|
77.5" (1,969 mm)
|
89.5" (2,275 mm)
|
|
Time to Full Rise
|
60 seconds
|
N/A
|
|
Outside Dimensions
|
|
D - Overall Width
|
130" (3,304 mm)
|
(±.125 in. / 3 mm) 130" (3,304 mm)
|
|
E - Outside Length
|
213" (5,410 mm)
|
243" (6,170 mm)
|
|
F - Overall Length
|
242" (6,147 mm)
|
272" (6,907 mm)
|
|
G - Height of Columns
|
92" (2,337 mm)
|
104" (2,643 mm)
|
|
Inside Dimensions
|
|
H - Width Between Columns
|
120" (3,048 mm)
|
|
I - Drive-Thru Clearance
|
98" (2,489 mm)
|
98.25" (2,489 mm)
|
|
Runways
|
|
J - Runway Width
|
20" (508 mm)
|
19" (482 mm)
|
|
K - Length of Runways
|
197.5" (5,017 mm)
|
227.5" (5,777 mm)
|
|
L - Width Between Runways
|
34.5" or 41.5" (876 or 1,054 mm)
|
35.75" or 42" (910 or 1,068 mm)
|
|
M - Runway Centerline
|
57.5" or 64.5" (1,461 or 1,638 mm)
|
|
N - Outside Edge of Runways
|
77.5" or 84.5" (1,969 or 2,146 mm)
|
|
Minimum Wheelbase
|
|
Rated Capacity
|
140" (3,556 mm)
|
* 135" (3,429 mm)
|
|
75% Capacity
|
120" (3,048 mm)
|
* 115" (2,921 mm)
|
|
50% Capacity
|
100" (2,540 mm)
|
* 95" (2,413 mm)
|
|
25% Capacity
|
* 80" (2,032 mm)
|
|
Locking
|
|
Locking Positions
|
15
|
17
|
|
Lock Spacing
|
Every 4" (102 mm)
|
|
Power Unit
|
|
Motor
|
220 VAC / 60 Hz / 1Ph
|
|
Noise
|
45 dB
|
N/A
|
|
Shipping
|
|
Weight
|
2,606-lbs. (1182 kg)
|
N/A
|
|
Dimensions
|
209" x 22" x 29"
(5359 mm x 610 mm x 737 mm)
|
N/A
|
To View or Download Specification Image Click Here
Note: An air supply (minimum: 30 psi / 3 CFM) is required for the safety-lock mechanisms to disengage. It is solely the responsibility of the end-user to provide, install and maintain the air supply.
* The Lift supports less weight than its rated capacity if the Vehicle’s wheelbase is shorter; this is because the wheels are closer to the middle of the Runways, where there is less support. For example, the maximum weight allowed on the Lift for a Vehicle with a wheelbase of 85 in. is 50 percent of the Lift’s rated capacity (or 7,000 lbs. when the rated capacity is 14,000 lbs.).
2 Special voltages available upon.
*Not all BendPak lift models meet the standards as prescribed by ANSI/ALI ALCTV (Current Edition)or ANSI/UL 201. Consult
www.autolift.org for a complete list.
Better Products – Better Service – Better Value
Duration: From the date of purchase by the original Purchaser or 60-24-12 months from the date of shipment by BendPak or whichever comes first.
a Five Years (60-Months) Bumper-to-Bumper Warranty on the lift structure
a Two Years (24-Months) Warranty on the hydraulic cylinder(s) and power unit
a One Year (12-Months) Labor Warranty on site or at factory
a One Year (12-Months) Free-Shipping* on ground-freight charges related to warranty performance
Limited Warranty
- Who gives this warranty (Warrantor): BendPak Inc., 1645 lemonwood dr. Santa Paula, CA 93060
- Who receives this warranty (Purchaser): The original Purchaser (other than for purpose of resale)
- What products are covered by this warranty: Any BendPak Two-Post or Four-Post car lift**
- What is covered under this warranty: manufacturer defects due to material and/or workmanship with the exceptions noted below.
- What is not covered under this warranty:
- Any failure that results from Purchaser’s abuse, neglect or failure to operate, maintain or service product in accordance with instructions provided in the owner’s manual(s) supplied
- And damage caused by overloading lift beyond rated capacity
- Items or service normally required to maintain the product, i.e. lubricants, oil, etc.
- Items considered general wear parts such as rubber pads, lifting cables, etc. unless wear or failure is a direct result of manufacturer defect due to material and/or workmanship
- Any component damaged in shipment or any failure caused by installing or operating lift under conditions not in accordance with installation and operation guidelines or damaged by contact with tools or surroundings
- Motor or pump failure caused by rain, excessive humidity, corrosive environments or other contaminants
- Rusted components due to improper maintenance or corrosive environments
- Cosmetic defects that do not interfere with product functionality
- Damage due to incorrect voltage or improper wiring
- Any incidental, indirect, or consequential loss, damage, or expense that may result from any defect, failure, or malfunction of BendPak Inc product
- Responsibilities of Warrantor under this warranty: Repair or replace, at Warrantor’s option, component which is defective, has malfunctioned and/or failed to conform within duration of the warranty period. BendPak Inc. will pay reasonable labor costs for the first 12 months only
- Responsibilities of Purchaser under this warranty:
- Provide dated proof of purchase and maintenance records
- In some cases, components may be required to be shipped to the nearest BendPak Authorized Service Center. Freight costs, after 12-months, must be borne by the Purchaser.
- Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).
- When Warrantor will perform repair or replacement under this warranty: Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts.
*Free-shipping applies to direct shipping points within the 48 continental United States. Rural area shipping surcharge may apply for remote addresses. **For all BendPak brand two-post and four-post surface mounted lifts manufactured on or following 1/1/2011.
Limitation of Liability
In no event will either party be liable for any damage caused by the other party's failure to fulfill its responsibilities under these terms and conditions. In no event will either party be liable for any lost profits, lost savings, incidental damage, or other economic consequential damages. All expressed and implied warranties, including the implied warranties of merchantability and fitness for a particular purpose, are limited in duration to the coverage period. No warranties, expressed or implied, will apply after this period. BendPak may modify these terms and conditions at any time by either providing the customer with written notice or posting such revised terms on www.bendpak.com. Such revised terms shall be effective thirty days from the date of such written notice or posting.
https://bendpakcs.freshdesk.com/a/tickets/new
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features
- 14,000-lb. lifting capacity
- CE Approved and Certified. Meets or exceeds the standards prescribed by European Standard EN-1493
- Mid to long-style approach ramps for low ground clearance vehicles
- Runways include rail-kit for optional accessories
- Single hydraulic cylinder mounted underneath runway
- Fully enclosed lifting cables, safety locks and sheaves
- Internal anti-sway slider blocks in each column
- Pneumatic push-button safety release
- Heavy-duty 1/2" aircraft cable and 1.75" roller axles
- Safety locks enclosed in columns minimize pinch points
- Oversized sheave diameter reduces cable fatigue
- Oversized self-lubricating cable rollers
- Rugged 1.75" roller axles
- Multi-position safety locks in each column
- Customizable power unit location
- Approach ramps incorporate built-in rear-wheel chocks
- Independent backup slack-cable safety latches
|
|
|
|
|
|
|
Owned & Operated in the U.S. since 1987
