 |
BendPak BendPak 10APS-168 Symmetric Ex-Tall 2 Post Car Lift 10,000 lb. Capacity
NOT ALI Certified
A New Paradigm in Lifting
BendPak’s all-new AP series of two-post lifts are a revolutionary design that factors the best qualities of today’s two-post lift types into a completely new concept in car lift engineering. The result is a lift unlike any other on the market, purposefully designed for extreme use, high loads and operator efficiency.
Forecasters are projecting Electric Vehicles (EV’s) to account for a large percentage of all vehicles produced and sold in the future and EV’s weigh considerably more than traditional gasoline or diesel powered vehicles. Those extra pounds have important implications for mechanic safety when these vehicles are raised in the air for service. Extra vehicle weight induces a lot more stresses and forces on automotive lift components, especially when two-post lifts are being considered. With the emergence of heavier vehicles as the impetus for the new 10AP design, BendPak engineers focused on the use of higher tensile-strength steels for the swing arms and other critical load-holding components, and the introduction of safety-critical design enhancements throughout.
Automatic Arm Restraint System (AARS) Prevents Unplanned Movement
A significant design feature that makes BendPak’s AP series particularly well-suited for heavy vehicle service is a revolutionary automatic arm restraint system that has been bolstered to withstand elevated pushing and pulling forces that occur when vehicles are raised.
The new Automatic Arm Restraint System (AARS) is designed to ensure safety at all times, minimizing the risk of vehicle fall accidents during the lift use and vehicle service operations. The heavily forged-steel design of the AARS secures the lift arms firmly in place, preventing unplanned swing-arm movement during lift use and vehicle service operations. With a constant restraining force applied on the swing arms during all lifting p, accidental arm creep resulting in sudden arm shift and unplanned rapid extraction, the leading contributing factor in vehicle falls, is safely mitigated.
|
Model
|
10APS
|
10APS-168
|
10APXS
|
10APXS-181
|
|
Capacity
|
|
Lifting Capacity: (*)
|
10,000 lbs. (4,536 kg)
|
|
Rise
|
|
A - Lowered Pad Height
|
4.5” (114 mm)
|
|
B - Max. Lifting Height
|
80.5” (2,045 mm)
|
86.5” (2,197 mm)
|
|
C - Lowest Lock Position
|
24” (610 mm)
|
|
D - Top Lock Position
|
73” (1,854 mm)
|
79” (2,007 mm)
|
|
Time to Full Rise
|
45 seconds
|
|
Height Overall
|
|
E - Height Overall
|
145” (3,683 mm)
|
168” (4,267 mm)
|
157” (3,988 mm)
|
181” (4,597 mm)
|
|
F - Width Overall
|
139” or 147” (3,531 mm or 3,734 mm)
|
|
G - Outside Column Width
|
128” or 136” (3,251 mm or 3,454 mm)
|
|
Inside Column Width
|
|
H - Inside Columns
|
109” or 117” (2,769 mm or 2,972 mm)
|
|
I - Drive-Thru Clearance
|
92” or 100” (2,337 mm or 2,540 mm)
|
|
J - Floor To Overhead Switch
|
140” (3,556 mm)
|
163” (4,140 mm)
|
152” (3,861 mm)
|
176” (4,470 mm)
|
|
Arms & Pads
|
|
K - Front Arm Reach (Short)
|
24” - 47” (610 mm - 1,194 mm)
|
|
L - Rear Arm Reach (Long)
|
31.5” - 59” (800 mm - 1,499 mm)
|
|
Max Load Per Arm
|
2,500 lbs. (1,134 kg)
|
|
Electrical
|
|
Motor
|
220 VAC / 60 Hz. / 1Ph
|
The design, material and specifications are subject to change without notice.
*Not all BendPak lift models meet the standards as prescribed by ANSI/ALI ALCTV (Current Edition) or ANSI/UL 201. Consult
www.autolift.org for a complete list.
Better Products – Better Service – Better Value
LIMITED WARRANTY. Subject to the limitations of set forth below, Warrantor warrants that the Product sold hereunder conform to Warrantor's
published specifications. WARRANTOR MAKES NO REPRESENTATION OR WARRANTY OF ANY OTHER KIND, EXPRESS OR IMPLIED, WITH RESPECT TO
THE GOODS, WHETHER AS TO MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER MATTER
Duration: From the date of purchase by the original Purchaser or 60-24-12 months from the date of shipment by BendPak or whichever comes first.
- Five Years (60-Months) Warranty on the lift structure
- Two Years (24-Months) Warranty on the hydraulic cylinder(s) and power unit
- One Year (12-Months) Warranty on operating components
- One Year (12-Months) Warranty on electrical components (excluding power unit)
- One Year (12-Months) Labor Warranty on site or at factory*
- One Year (12-Months) Free-Shipping** on ground-freight charges related to warranty performance
Limited Warranty
- Who gives this warranty (Warrantor): BendPak Inc., 1645 lemonwood dr. Santa Paula, CA 93060
- Who receives this warranty (Purchaser): The original Purchaser (other than for purpose of resale)
- What products are covered by this warranty: Any BendPak Two-Post or Four-Post car lift***
- What is covered under this warranty: manufacturer defects due to material and/or workmanship with the exceptions noted below.
- What is not covered under this warranty:
- Any failure that results from Purchaser’s abuse, neglect or failure to operate, maintain or service product in accordance with instructions provided in the owner’s manual(s) supplied
- Any damage caused by overloading Product beyond rated capacity
- Items or service normally required to maintain the product, i.e. lubricants, oil, etc.
- Items considered general wear parts such as rubber pads, lifting cables, etc. unless wear or failure is a direct result of manufacturer defect due to material and/or workmanship
- Any component damaged in shipment or any failure caused by installing or operating lift under conditions not in accordance with installation and operation guidelines or damaged by contact with tools or surroundings
- Motor or pump failure caused by rain, excessive humidity, corrosive environments or other contaminants
- Rusted components due to improper maintenance or corrosive environments
- Cosmetic defects that do not interfere with product functionality
- Damage due to incorrect voltage or improper wiring
- Any failure that results from improper installation or use not according to specifications
- Damage caused by disasters such as fire, flood, wind, and lightning
- Damage caused by unauthorized attachments or modifications
- Responsibilities of Warrantor under this warranty: Repair or replace, at Warrantor’s option, component which is defective, has malfunctioned and/or failed to conform within duration of the warranty period. BendPak Inc. will pay reasonable labor costs for the first 12 months only
- Responsibilities of Purchaser under this warranty:
- Provide dated proof of purchase and maintenance records
- In some cases, components may be required to be shipped to the nearest BendPak Authorized Service Center. Freight costs, after 12-months, must be borne by the Purchaser.
- Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).
- Immediately upon receipt of the Product, Purchaser shall inspect the same. Any claim for shortage must be made within ten days after Purchaser's receipt. All other claims, including claims for alleged defective Product, must be made within fifteen days after Purchaser learns of the facts upon which such claim is based, but in no event later than the applicable one, two or five year period specified above for the specified component(s). All claims not made in writing and received by Seller within the time periods specified above shall be deemed waived. With respect to any defects incapable of discovery until in use, all claims for any
damages or losses as a result of such defects shall be deemed waived unless made in writing and received by Seller within fifteen days after Purchaser learns of the alleged defect giving rise to the claim and after the expiration of said periods, but in no event later than the applicable one, two or five year period specified above for the specified component(s). Purchaser expressly assumes all liability for all such damages or losses, irrespective of any use which shall have taken place or whether the alleged defect shall have occurred or been discovered prior to expiration of such periods.
- When Warrantor will perform repair or replacement under this warranty: Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts.
*As determined by Warrantor in its sole discretion**Free-shipping applies to direct shipping points within the 48 continental United States.
Rural area shipping surcharge may apply for remote addresses. ***For all BendPak brand Two-Post or Four-Post Vehicle Service Lifts
(excluding specialty lifts, high rise, commercial parking, material handling, or models for particular purpose) manufactured on or following
1/1/2011.
https://bendpakcs.freshdesk.com/a/tickets/new
|
|
|
Owned & Operated in the U.S. since 1987
