BendPak HDSO-14 Open Front 4 Post Car Lift 14,000 lb. Capacity

Description

Technical Specifications

Warranty

BendPak HDSO-14P 14,000 lb Open Front Car Lift

To view the lift inspection guide Click Here

The HDSO-14P is an open-front four-post lift that features clear-entry up front providing easy vehicle access. A generous 14,000-lb. lifting capacity and extended runways allow you to service a wide variety of vehicles ranging from small cars to full-size trucks.

Open-Front Design

We engineered the HDSO-14P without a front cross bar so the operators can easily enter and exit from beneath the vehicle. Now the process of front-end adjustment becomes quick and trouble-free. This is a must for busy alignment bays.

Patented adjustable front outrigger tubes
For precise front-lift leveling, nothing beats our patented adjustable front outrigger tubes. The infinitely adjustable pitch compensates for excessive loads and even unlevel floors.

Dependable design
Four heavy-duty, high-quality, stainless steel lifting cables and a single hydraulic cylinder mounted underneath the runway makes this lift the most durable, maintenance-free lifting system on the market.

Oversize dual-hub cable sheaves
Huge 10‐1/2” diameter cable sheaves within the runway and cross tubes combined with massive 2‐1/4” diameter sheave axles dramatically improve cable wear and critical component lifespan meaning you’ll spend less money in service related expenses down the road. Dual‐hub cable sheaves reduce stress, fatigue and wear.

Multi-level locking positions
The HDSO-14 is equipped with multiple adjustable height locking positions for variable-height parking. A convenient push-button pneumatic safety lock control releases all four independent safety locks simultaneously.

Heavy-duty aircraft cable
Each lift is supplied with 4 high-quality ½” diameter 6 x 25 stainless steel lifting cables, rated at 14,400 lbs. each. The combined rating of these cables is more than 411% of the maximum lifting capacity of the entire lift! This aircraft‐quality cable was specifically designed for lifting applications and provides a great balance between abrasion resistance and fatigue. And we make sure it looks tidy too—all lifting cables are fully enclosed within the lift structure itself.

Maintenance-free electric hydraulic
A maintenance‐free electric hydraulic power system assures ultimate dependability.

Grease nipples
Grease nipples are located on every sheave and sheave axle to make lubrication maintenance a breeze.

Electric / hydraulic power system
We incorporate maintenance-free electric hydraulic power systems into each lift for ultimate dependability, and all controls are conveniently located within close reach.

Large base plates
12” x 10” base plates provide a solid foundation for the HDSO-14.

Single hydraulic cylinder

The HDSO-14 open-front lift is equipped with a single hydraulic cylinder hidden away under the runway for minimum exposure and maximum reliable performance. Our industrial-grade hydraulic cylinders feature a single-piece, pilot fitted, machined steel piston, wrapped with specially designed, pressure loaded U-cup piston seals, backups and wear bands to virtually eliminate fluid bypass. The micro-smooth chrome rod is machined from high-yield, ground and polished C-1045/50 micro-alloy steel and plated to a minimum of .001” diametrically, to ensure superior cylinder operation and life. The superior design high durometer, mechanically-loaded rod seals make rod leakage is a thing of the past while a specially formulated abrasion-resistant urethane rod wiper provides exclusion protection. The welded cylinder body is made from robust steel tubing produced to exceed ASTM specifications. This combination of superb base material and superior processing ensures that the cylinders remain straight, smooth and last a very long time. An integrated flow restrictor provides a controlled descent in the case of an unexpected hose rupture.

Durable powder-coat finish
All HD-Series lifts feature a durable powder-coat finish that gives the metal a high-quality, extremely durable finish which can withstand even the harshest environmental or chemical conditions. Unlike other companies that claim to powder coat, we take pride in our meticulous 10-step process. First, all parts are visually inspected before being sandblasted. Afterwards, the parts are washed in our 5-stage phosphate tanks that can accommodate parts up to 25’ long. Once cleaned, they’re immediately dried to avoid rust production, and then outgassed. Outgassing pre-bakes the parts in a curing oven, reducing the possibility of blemishes that may be hiding in the pores of the metal. If not properly outgassed, imperfections in the metal may bubble during the curing process and most likely will cause chips in the powder. After the parts are washed and outgassed, any surfaces and / or threaded holes that need to be masked or plugged, are done so with high-temperature masking tape and silicone plugs. Next, the parts are given a quick thinner wipe to remove any light debris or fingerprints, before being hung on an electrostatically grounded conveyor line. The powder is finally applied using an electrostatic spray gun. The powder “sticks” to the surface in a fashion similar to how dust sticks to a television screen. Once the parts are powder coated, the carts are rolled into our curing oven and baked at 400° F for 45 minutes.

Non-skid runways
Gives you maximum grip, even when the runway surface is wet or oily.

Longer approach ramps
These approach ramps were designed a little longer to help when loading low ground clearance vehicles. It’s the little bit that makes a big difference.

Integrated design
Lifting cables, airlines, safety latches and sheaves are all fully enclosed.

Integrated hydraulic flow
An integrated hydraulic flow restrictor provides a controlled descent in the unlikely event of an unexpected hose rupture.

Automatic safety locks
Aircraft-quality stainless steel and aluminum pneumatic cylinders release all 4 locks simultaneously with the simple push of a button. The spring-loaded safety locks automatically engage continuously as the lift is raised. For added safety, a secondary lock system acts as a slack-cable device to engage in the unlikely event of cable failure.

Optional 7000 pound capacity rolling jacks

Optional 7000 pound capacity rolling jacks (model RJ-7) make a great addition to increase service capacity. RJ-7 bridge jacks are used to raise the front or rear portion of a vehicle off the runways allowing operators to perform efficient wheel and brake service. A pair of jacks allows the entire vehicle to elevated. Each jack has telescoping arms and frame contact pads that can be extended over the runways and positioned under vehicle lifting points. Telescoping rail supports accommodate adjustable runways for different tread widths. Each jack features three safety‐lock positions and stackable truck and van adapters for increased lifting height and better access to frame contact points on high ground‐clearance vehicles. The jacks come equipped with a commercial grade air‐hydraulic pump requiring a maximum pressure of 125 PSI and 10-20 CFM.

Model	HDSO14P	HDSO14AX
Capacity
Lifting Capacity: (*)	14,000 lbs. (6,350 kg)
*Max Capacity / Front Axle	7,000 lbs. (3,175 kg)
*Max Capacity / Rear Axle	7,000 lbs. (3,175 kg)
Rise
A - Min. Runway Height	7.625" (194 mm)
B - Max. Rise	70" (1,778 mm)
C - Max. Lifting Height	77.625" (1,972 mm)
Time to Full Rise	60 seconds
Outside Dimensions
D - Overall Width Front	143” (3,632 mm)
E - Overall Width Rear	130” (3,301 mm)
F - Outside Length	215.5" (5,473 mm)	215" (5,472 mm)
G - Overall Length	244" (6,198 mm)	243" (6,191 mm)
H - Height of Columns Front	105" (2,664 mm)
I - Height of Columns Rear	103” (2,613 mm)
Inside Dimensions
J - Width Between Columns Front	123” (3,124 mm)
K - Width Between Columns Rear	120” (3,046 mm)
L - Drive-Thru Clearance	97” (2,464 mm
Runways
M - Runway Width	20" (508 mm)	20.5” (520 mm)
N - Length of Runways	199" (5,054 mm)
O - Width Between Runways	45" (1,143 mm)
P - Runway Centerline	65" (1,651 mm)	N/A
Q - Outside Edge of Runways	85" (2,159 mm)	N/A
Wheel Alignment
Min. 4-Wheel Alignment	N/A	89" (2,261 mm)
Max. 4-Wheel Alignment	N/A	156" (3,962 mm)
Max. 2-Wheel Alignment	N/A	182" (4,420 mm)
Minimum Wheelbase
Rated Capacity	140" (3,556 mm)
75% Capacity	120" (3,048 mm)
50% Capacity	100" (2,540 mm)
25% Capacity	80" (2,032 mm)
Locking
Locking Positions	13
Lock Spacing	Every 4" (102 mm)
Power Unit
Motor	220 VAC / 60 Hz / 1Ph
Noise	45 dB
Shipping
Weight	3,099-lbs. (1,405 kg)	3,586-lbs. (1,626 kg)
Dimensions	218" x 22" x 50" (5,537 mm x 558 mm x 1,282 mm)	240" x 23" x 41" (6,096 mm x 584 mm x 1,041 mm)

Note: An air supply (minimum: 30 psi / 3 CFM) is required for the safety-lock mechanisms to disengage. It is solely the responsibility of the end-user to provide, install and maintain the air supply.

*Not all BendPak lift models meet the standards as prescribed by ANSI/ALI ALCTV (Current Edition) or ANSI/UL 201. Consult www.autolift.org for a complete list.

Click on Image to Enlarge or Download It

Better Products – Better Service – Better Value

Duration: From the date of purchase by the original Purchaser or 60-24-12 months from the date of shipment by BendPak or whichever comes first.

a Five Years (60-Months) Bumper-to-Bumper Warranty on the lift structure

a Two Years (24-Months) Warranty on the hydraulic cylinder(s) and power unit

a One Year (12-Months) Labor Warranty on site or at factory

a One Year (12-Months) Free-Shipping* on ground-freight charges related to warranty performance

Limited Warranty

Who gives this warranty (Warrantor): BendPak Inc., 1645 lemonwood dr. Santa Paula, CA 93060
Who receives this warranty (Purchaser): The original Purchaser (other than for purpose of resale)
What products are covered by this warranty: Any BendPak Two-Post or Four-Post car lift**
What is covered under this warranty: manufacturer defects due to material and/or workmanship with the exceptions noted below.
What is not covered under this warranty:
- Any failure that results from Purchaser’s abuse, neglect or failure to operate, maintain or service product in accordance with instructions provided in the owner’s manual(s) supplied
- And damage caused by overloading lift beyond rated capacity
- Items or service normally required to maintain the product, i.e. lubricants, oil, etc.
- Items considered general wear parts such as rubber pads, lifting cables, etc. unless wear or failure is a direct result of manufacturer defect due to material and/or workmanship
- Any component damaged in shipment or any failure caused by installing or operating lift under conditions not in accordance with installation and operation guidelines or damaged by contact with tools or surroundings
- Motor or pump failure caused by rain, excessive humidity, corrosive environments or other contaminants
- Rusted components due to improper maintenance or corrosive environments
- Cosmetic defects that do not interfere with product functionality
- Damage due to incorrect voltage or improper wiring
- Any incidental, indirect, or consequential loss, damage, or expense that may result from any defect, failure, or malfunction of BendPak Inc product
Responsibilities of Warrantor under this warranty: Repair or replace, at Warrantor’s option, component which is defective, has malfunctioned and/or failed to conform within duration of the warranty period. BendPak Inc. will pay reasonable labor costs for the first 12 months only
Responsibilities of Purchaser under this warranty:
- Provide dated proof of purchase and maintenance records
- In some cases, components may be required to be shipped to the nearest BendPak Authorized Service Center. Freight costs, after 12-months, must be borne by the Purchaser.
- Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).
When Warrantor will perform repair or replacement under this warranty: Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts.

*Free-shipping applies to direct shipping points within the 48 continental United States. Rural area shipping surcharge may apply for remote addresses. **For all BendPak brand two-post and four-post surface mounted lifts manufactured on or following 1/1/2011.

Limitation of Liability

In no event will either party be liable for any damage caused by the other party's failure to fulfill its responsibilities under these terms and conditions. In no event will either party be liable for any lost profits, lost savings, incidental damage, or other economic consequential damages. All expressed and implied warranties, including the implied warranties of merchantability and fitness for a particular purpose, are limited in duration to the coverage period. No warranties, expressed or implied, will apply after this period. BendPak may modify these terms and conditions at any time by either providing the customer with written notice or posting such revised terms on www.bendpak.com. Such revised terms shall be effective thirty days from the date of such written notice or posting.

https://bendpakcs.freshdesk.com/a/tickets/new

Features

14,000-lb. lifting capacity
CE Approved and Certified. Meets or exceeds the standards prescribed by European Standard EN 1493
Huge cable sheaves reduce wear and tear
Extremely convenient open-front design for easy access
Extended runway length for servicing
Longer approach ramps for low ground clearance vehicles
Electric / hydraulic power system
Runways include rail-kit for optional accessories
Runways adjust for different tread widths
Automatic leveling system with multiple auto-leveling locking positions
Single hydraulic cylinder mounted underneath runway
Fully enclosed lifting cables, safety locks, and sheaves
Internal anti-sway slider blocks in each column
Pneumatic push-button safety release
Features heavy-duty 1/2" aircraft cable
Safety locks enclosed in columns minimize pinch points
Oversized sheave diameter reduces cable fatigue
Runways feature non-skid surface
Rugged, self-lubricating cable sheaves
Features 1-3/8” sheave axles
Multi-position safety locks in each column
Independent backup slack-cable safety latches
Includes fully adjustable lock stops for precise leveling
Integrated rolling bridge airline kit option available
Roll-back kit options available
Optional drive-thru ramps available
Optional drip trays available
Optional 7,000-lb. capacity rolling jacks available (Model RJ-7)

Optional # 5210142 Add-On Alignment Kit - Available While Supplies Last

This Alignment Kit is designed to fit all standard 9K, 12K, and 14K four‐post lifts with minimum 19” wide runways. This wheel alignment kit provides the necessary rear slip plates, turnplate pockets and commercial‐grade turnplates to convert your standard four‐post lift into an economical solution for performing two and four‐wheel alignments.

Kit Includes