 |
 |
 |
|
BendPak MDS-6KLPF 6,000-lb. Open Center Mid-Rise Scissor Flush Mount Lift
Supersedes MSD-6KF
To view or download the lift inspection guide
Click Here.
Stronger lift from a collapsed position
A pneumatic "kick" powers the lift up from the collapsed height, which for a flush-mount means it goes from zero-footprint to full rise in about 45 seconds. This extra boost ensures a more even lift in the early inches, and the hydraulics take over from there.
Four hydraulic cylinders
We put enough power in this scissor lift to ensure it handles that 6,000-lb. load without a hitch. Fluid traveling to all four cylinders goes through a flow divider to ensure equal pressure at all times. The platforms are always going to rise and descend simultaneously every inch of the way.
Solid-steel safety lock bars
With three locking positions to choose from, the MDS-6LPF offers incredible work height versatility. If you've got a pit, the mid-rise design becomes a full-height service lift.
Convenient stainless-steel pneumatic cylinders
Instead of spring releases, which tend to wear over time, our flush-mount design features air cylinders pressurized to 50 psi, 10-CFM. A simple hand pump or air compressor will have the cylinders ready to go in seconds.
A push-button safety lock release system
The push of a button releases all locks simultaneously and quickly lowers the scissor lift platforms down to their flush-mounted starting position.
Hinge-point features Zerk grease fittings
Zerk grease fitting are long-lasting, self-lubricating and simple to maintain. They'll virtually last forever with minimal care.
Durable, cushioned rubber contact blocks
Hard rubber blocks come standard with your lift purchase. No small, dinky pads here. These rugged lifting tools will protect your vehicles' frames and are guaranteed not to slip when properly placed during lifting procedures.
NOTE: The lift platform and contact blocks allow lifting of most unibody and frame contact undercarriages at recommended manufacturer pick-up points on most vehicles. Be sure to compare your vehicle specifications, including ground clearance and overall height, with the specifications shown before you purchase.
Detailed installation and maintenance instructions
We include a full installation and training/service manual, along with safety decals and stickers, for your convenience.
|
Specifications
|
MDS-6LP
|
MDS-6LPF
|
|
Style
|
|
|
Surface Mount
|
Flush Mount
|
|
Capacity
|
|
Lifting Capacity
|
6,000 lbs. / 2,722 kg
|
|
Rise
|
|
Lifting Height
|
44" (1,118 mm)
|
44" (1,118 mm)
( minus 4-3/8" for sub-surface flooring)
|
|
Lifting Height w/Blocks
|
46" (1,168 mm)
|
46" (1,168 mm)
( minus 4-3/8" for sub-surface flooring)
|
|
Outside Dimensions
|
|
Lift Platform Dimensions
|
19" x 67" (484 mm x 1,701 mm)
|
|
Width Between Platforms
|
40" to 46" (1,018 mm to 1,168 mm)
|
|
Overall Width
|
Adjustable
|
|
Overall Length
|
92.6" (2,351 mm)
|
67" (1,701 mm)
|
|
Lowered Height
|
5" (127 mm)
|
Flush with Ground
|
|
Locking Heights
|
|
Fully Lowered
|
5" (127 mm)
|
|
1st Lock Position
|
21" (533 mm)
|
|
2nd Lock Position
|
32" (813 mm)
|
|
3rd Lock Position
|
38.75" (984 mm)
|
|
Full Rise
|
44" (1,118 mm)
|
|
Power Unit
|
|
Motor
|
208-230 VAC / 60 Hz / 1 Ph
|
|
Lifting time
|
35 sec
|
|
Shipping
|
|
Shipping Weight
|
1,620-lbs. (735 kg)
|
1,422-lbs. (645 kg)
|
|
Shipping Dimensions
|
70" x 67" x 23"
(1,778 mm x 1,701 mm x 597 mm)
|
70" x 61" x 25"
(1,778 mm x 1,549 mm x 635 mm)
|
Not all BendPak lift models meet the standards as prescribed by ANSI/ALI ALCTV (Current Edition) or ANSI/UL 201. Consult
www.autolift.org for a complete list.
LOW-RISE/MID-RISE LIFTS WARRANTY
Duration: From the date of purchase by the original Purchaser or 12-24 months from the date of shipment by BendPak or whichever comes first.
- Two Years (24-Months) Warranty on the lift structure
- One Year (12-Months) Warranty on the hydraulic cylinder(s) and power unit
- One Year (12-Months) Warranty on operating components
- One Year (12-Months) Labor Warranty on site or at factory
- One Year (12-Months) Free-Shipping* on ground-freight charges related to warranty performance
Limited Warranty
1. Who gives this warranty (Warrantor): BendPak Inc., 1645 Lemonwood Dr., Santa Paula, CA 93060
2. Who receives this warranty (Purchaser): The original Purchaser (other than for purpose of resale)
3. What products are covered by this warranty: Any BendPak Full-Rise Scissor Lift**
4. What is covered under this warranty: manufacturer defects due to material and/or workmanship with the exceptions noted below.
5. What is not covered under this warranty:
a. Any failure that results from Purchaser’s abuse, neglect or failure to operate, maintain or service product in accordance with instructions provided in the owner’s manual(s) supplied
b. Any damage caused by overloading lift beyond rated capacity
c. Items or service normally required to maintain the product, i.e. lubricants, oil, etc.
d. Items considered general wear parts such as rubber pads, pad adapters, etc. unless wear or failure is a direct result of manufacturer defect due to material and/or workmanship
e. Any component damaged in shipment or any failure caused by installing or operating lift under conditions not in accordance with installation and operation guidelines or damaged by contact with tools or surroundings
f. Motor or pump failure caused by rain, excessive humidity, corrosive environments or other contaminants
g. Rusted components due to improper maintenance or corrosive environments
h. Cosmetic defects that do not interfere with product functionality
i. Damage due to incorrect voltage or improper wiring
j. Any incidental, indirect, or consequential loss, damage, or expense that may result from any defect, failure, or malfunction of BendPak Inc. product
k. All electrical components are guaranteed for one year against defects in workmanship and/or materials when the lift is installed and used according to specifications.
6. Responsibilities of Warrantor under this warranty: Repair or replace, at Warrantor’s option, component which is defective, has malfunctioned and/or failed to conform within duration of the warranty period. BendPak Inc. will pay reasonable labor costs for the first 12 months only
7. Responsibilities of Purchaser under this warranty:
a. Provide dated proof of purchase and maintenance records
b. In some cases, components may be required to be shipped to the nearest BendPak Authorized Service Center. Freight costs, after 12-months, must be borne by the Purchaser.
c. Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).
8. When Warrantor will perform repair or replacement under this warranty: Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts.
*Free-shipping applies to direct shipping points within the 48 continental United States. Rural area shipping surcharge may apply for remote
addresses.
**For all BendPak brand Low-Rise and Mid-Rise Surface Mounted Vehicle Service Lifts (excluding specialty lifts, high rise, commercial
parking, material handling, or models for particular purpose) manufactured on or following 7/27/2012.
Limitation of Liability
BendPak/Ranger shall have no obligation pursuant to this Warranty with respect to products which in our sole judgment have been altered
damaged, misused, abused, badly worn, lost or improperly maintained. This Warranty is null and void if the customer or any other person other
than an authorized representative of BendPak/Ranger has made any attempt to service or modify the tool prior to its return to BendPak/Ranger
under this Warranty. In no event will either party be liable for any damage caused by the other party's failure to fulfill its responsibilities under
these terms and conditions. In no event will either party be liable for any lost profits, lost savings, incidental damage, or other economic
consequential damages. All expressed and implied warranties, including the implied warranties of merchantability and fitness for a particular
purpose, are limited in duration to the coverage period. No warranties, expressed or implied, will apply after this period. BendPak may modify
these terms and conditions at any time by either providing the customer with written notice or posting such revised terms on
www.bendpak.com. Such revised terms shall be effective thirty days from the date of such written notice or posting.
https://bendpakcs.freshdesk.com/a/tickets/new
|
|
|
 |
|
 |
|
Owned & Operated in the U.S. since 1987
