 |
 |
 |
|
BendPak PCL-16HD-6 99,000 lb. Mobile 6 Column Hydraulic Lifting System
The BendPak PCL-16HD-6 99,000 lb. Mobile 6 Column Hydraulic Lifting System Features:
Whether you need to lift a bus, fleet vehicle, or fire truck, BendPak's PCL-16HD lift system is designed to meet your needs. This super-duty portable column lift system has a combined lifting capacity of 99,000 lbs. and takes just over one minute to reach the maximum lifting height of 67". Each column features a mechanical locking system, flow control check valve, pressure relief valve and trouble-free hydraulics for increased safety and reliability. A unique hydraulic control system allows operators to lower the columns manually in the event of a power supply failure. Microprocessor controls combined with a unique hydraulic
synchronization system ensures very smooth movement over the entire journey; from floor, to maximum lifting height and back. A hydraulic pallet-truck mechanism, coupled with a tight turning radius, enables one person to move the columns effortlessly. The PCL-16HD system's controls are easy to use and feature up / down and emergency stop buttons. Includes the added convenience of three separate operation modes: single, pair or set.
The PCL-16HD-6 is the six-post configuration of the PCL-16HD series. If you need a four-post configuration, check out the PCL-16HD-4.
Features
- 16,500-lb. individual column capacity
- 99,000-lb. maximum system capacity
- Four modes of operation: single, pair or all six
- 67" lifting height for tall mechanics
- Extended 15" forks accommodate super-wide tires and deep wheel configurations
- Multi-width wheel forks with locking pins accommodate the widest range of wheels eliminating the need for specialty wheel adapters
- Integrated electronic feature self diagnostics functions
- Independent column control stations eliminate the need for a single master control column
- Trouble-free hydraulic lifting system
- Low power consumption
- Separate key lock security for each control box
- Fuse protected
- Sealed rollers on the wheels for easy movement of the columns
- Sealed roller bearings on carriages for a lifetime of trouble-free service
- Space-saving design and reduced column weight
- A tight turning radius provides easy mobility
- Automatic synchronization and communication between columns for precise, level lifting
- Multiple, automatic, independent safety locks ensure safe operation
- Quick-disconnect plugs at each column for fast and efficient set up
- Simple operation, long service life and minimum maintenance
- Operator monitoring and automatic leveling control
- Set the vehicle on jack stands and use the columns to raise another vehicle in an adjoining bay
- Low-profile fork angle for easy positioning of columns, especially for floatation tires
- Low mounted weight distribution of power unit and controls means a low center of gravity, allowing the columns to move easier than top heavy screw-drive columns
- Durable powder-coat finish
- Max column capacity: 16,500 lbs. / 7,484 kg
- Max system capacity: 99,000 lbs. / 44,905 kg
- Min column height: 89" / 2,255 mm
- Max column height: 144-3/4" / 3,675 mm
- Max lifting height: 70" / 1,778 mm
- Length lifting fork: 15" / 381 mm
- Overall length: 47-3/4" / 1,210 mm
- Min width inside lifting fork: 11" / 280 mm
- Max width inside lifting fork: 23-1/2" / 597 mm
- Overall width: 43-1/2" / 1,100 mm
- Turning circle: 40" / 1,016 mm
- Column weight: 549 lbs. / 1,210 kg
- Lifting speed: 110 sec
- Motor: 2 Hp / 208 V – 230 V / 50 Hz – 60 Hz / 1 Ph
- Shipping weight: 1,394 lbs. / 634 kg (Ea. post)
- Shipping dimensions: 72" x 42" x 96" / 1,829 mm x 1,067 mm x 2,438 mm (Ea. post)
Better Products – Better Service – Better Value
Duration: From the date of purchase by the original Purchaser or 60-24-12 months from the date of shipment by BendPak or whichever comes first.
a Five Years (60-Months) Bumper-to-Bumper Warranty on the lift structure
a Two Years (24-Months) Warranty on the hydraulic cylinder(s) and power unit
a One Year (12-Months) Labor Warranty on site or at factory
a One Year (12-Months) Free-Shipping* on ground-freight charges related to warranty performance
Limited Warranty
- Who gives this warranty (Warrantor): BendPak Inc., 1645 lemonwood dr. Santa Paula, CA 93060
- Who receives this warranty (Purchaser): The original Purchaser (other than for purpose of resale)
- What products are covered by this warranty: Any BendPak Two-Post or Four-Post car lift**
- What is covered under this warranty: manufacturer defects due to material and/or workmanship with the exceptions noted below.
- What is not covered under this warranty:
- Any failure that results from Purchaser’s abuse, neglect or failure to operate, maintain or service product in accordance with instructions provided in the owner’s manual(s) supplied
- And damage caused by overloading lift beyond rated capacity
- Items or service normally required to maintain the product, i.e. lubricants, oil, etc.
- Items considered general wear parts such as rubber pads, lifting cables, etc. unless wear or failure is a direct result of manufacturer defect due to material and/or workmanship
- Any component damaged in shipment or any failure caused by installing or operating lift under conditions not in accordance with installation and operation guidelines or damaged by contact with tools or surroundings
- Motor or pump failure caused by rain, excessive humidity, corrosive environments or other contaminants
- Rusted components due to improper maintenance or corrosive environments
- Cosmetic defects that do not interfere with product functionality
- Damage due to incorrect voltage or improper wiring
- Any incidental, indirect, or consequential loss, damage, or expense that may result from any defect, failure, or malfunction of BendPak Inc product
- Responsibilities of Warrantor under this warranty: Repair or replace, at Warrantor’s option, component which is defective, has malfunctioned and/or failed to conform within duration of the warranty period. BendPak Inc. will pay reasonable labor costs for the first 12 months only
- Responsibilities of Purchaser under this warranty:
- Provide dated proof of purchase and maintenance records
- In some cases, components may be required to be shipped to the nearest BendPak Authorized Service Center. Freight costs, after 12-months, must be borne by the Purchaser.
- Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).
- When Warrantor will perform repair or replacement under this warranty: Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts.
*Free-shipping applies to direct shipping points within the 48 continental United States. Rural area shipping surcharge may apply for remote addresses. **For all BendPak brand two-post and four-post surface mounted lifts manufactured on or following 1/1/2011.
Limitation of Liability
In no event will either party be liable for any damage caused by the other party's failure to fulfill its responsibilities under these terms and conditions. In no event will either party be liable for any lost profits, lost savings, incidental damage, or other economic consequential damages. All expressed and implied warranties, including the implied warranties of merchantability and fitness for a particular purpose, are limited in duration to the coverage period. No warranties, expressed or implied, will apply after this period. BendPak may modify these terms and conditions at any time by either providing the customer with written notice or posting such revised terms on www.bendpak.com. Such revised terms shall be effective thirty days from the date of such written notice or posting.
|
|
|
 |
|
 |
|
|
| Accessories for this product... |
|
|
|
|
