 |
 |
 |
|
BendPak HD-9STX 9K lb. Narrow Width, High Lift Service and Parking Lift
The BendPak HD-9STX 9K lb. Narrow Width, High Lift Service / Parking Auto Lift Features:
Model: HD-9STX
Manufacturer: Bend-Pak
Weight: 1400.00
These HD-Series lift models were designed and built for car aficionados
who appreciate quality and value. Not just quality design but quality workmanship
throughout, and not value as in cheap but value as getting a lot more bang for your
buck. Sure, we could have made them cheaper, but then theyd be like all those non-
certified hobby lifts on the market. Please dont make the mistake of calling these
lifts hobby lifts. Our engineers would get offended. These full-blown lift models
come packed with features that until now were found only on commercial-grade
designs. Better yet, theyre built and backed by a company with over 35 years in the
business. Were proud to have these lifts in our lineup because they have one thing
in common with our great reputation. Both carry a lot of weight.
- 9,000 pound lifting capacity
- Optional caster kit available
- Freestanding design
- Perfect for PARKING, STORAGE or SERVICE.
- Runways include rail kit for optional accessories.
- Single hydraulic cylinder mounted underneath runway.
- Fully-enclosed lifting cables, safety locks, and sheaves.
- Internal "anti-sway" slider blocks in each column
- Pneumatic push-button safety release.
- Features heavy-duty 3/8" aircraft cable.
- Longer approach ramps for low ground clearance vehicles
- Safety locks enclosed in columns minimize pinch points.
- Oversized sheave diameter reduces cable fatigue.
- Rugged, self-lubricating cable sheaves combined with 1-1/4" sheave axles are fully enclosed minimizing pinch points.
- Multi-position safety locks in each column
- Power unit can be located at the front or rear of the lift.
- Designed to meet ANSI standards.
- Approach ramps can be removed for added clearance.
- Independent "back-up" slack-cable safety latches.
- Optional drive-thru ramps available.
- Optional drip trays available.
- Optional solid deck increases storage capacity.
- Optional 4,500 lb. "Low-Boy" air/hyd. rolling jacks available.
|
| Model |
HD-9STX |
| Lifting Capacity |
9,000lbs. / 4082 kg. |
| A - Overall Width |
103-3/4" / 2635 mm |
| B - Outside Length |
198" / 5029 mm |
| C - Overall Length |
224" / 5690 mm |
| D - Height of Columns |
100" / 2540 mm |
| E - Min. Runway Height |
4-1/2" / 114 mm |
| F - Max Rise |
82" / 2083 mm |
| G - Max. Lifting Height |
86-1/2" / 2197 mm |
| H - Width Between Posts |
89-3/4" / 2280 mm |
| I - Runway Width |
19" / 483 mm |
| J - Width Between Runways |
37-1/4" / 946 mm |
| K - Length of Runways |
188" / 4775 mm |
| Locking Positions |
15 |
| Lock Spacing |
Every 4" / 102 mm |
| Lifting Time |
50 Seconds |
| Standard Motor |
220 VAC / 60 Hz. 1Ph. |
|
Better Products – Better Service – Better Value
Duration: From the date of purchase by the original Purchaser or 60-24-12 months from the date of shipment by BendPak or whichever comes first.
a Five Years (60-Months) Bumper-to-Bumper Warranty on the lift structure
a Two Years (24-Months) Warranty on the hydraulic cylinder(s) and power unit
a One Year (12-Months) Labor Warranty on site or at factory
a One Year (12-Months) Free-Shipping* on ground-freight charges related to warranty performance
Limited Warranty
- Who gives this warranty (Warrantor): BendPak Inc., 1645 lemonwood dr. Santa Paula, CA 93060
- Who receives this warranty (Purchaser): The original Purchaser (other than for purpose of resale)
- What products are covered by this warranty: Any BendPak Two-Post or Four-Post car lift**
- What is covered under this warranty: manufacturer defects due to material and/or workmanship with the exceptions noted below.
- What is not covered under this warranty:
- Any failure that results from Purchaser’s abuse, neglect or failure to operate, maintain or service product in accordance with instructions provided in the owner’s manual(s) supplied
- And damage caused by overloading lift beyond rated capacity
- Items or service normally required to maintain the product, i.e. lubricants, oil, etc.
- Items considered general wear parts such as rubber pads, lifting cables, etc. unless wear or failure is a direct result of manufacturer defect due to material and/or workmanship
- Any component damaged in shipment or any failure caused by installing or operating lift under conditions not in accordance with installation and operation guidelines or damaged by contact with tools or surroundings
- Motor or pump failure caused by rain, excessive humidity, corrosive environments or other contaminants
- Rusted components due to improper maintenance or corrosive environments
- Cosmetic defects that do not interfere with product functionality
- Damage due to incorrect voltage or improper wiring
- Any incidental, indirect, or consequential loss, damage, or expense that may result from any defect, failure, or malfunction of BendPak Inc product
- Responsibilities of Warrantor under this warranty: Repair or replace, at Warrantor’s option, component which is defective, has malfunctioned and/or failed to conform within duration of the warranty period. BendPak Inc. will pay reasonable labor costs for the first 12 months only
- Responsibilities of Purchaser under this warranty:
- Provide dated proof of purchase and maintenance records
- In some cases, components may be required to be shipped to the nearest BendPak Authorized Service Center. Freight costs, after 12-months, must be borne by the Purchaser.
- Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).
- When Warrantor will perform repair or replacement under this warranty: Repair or replacement will be scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts.
*Free-shipping applies to direct shipping points within the 48 continental United States. Rural area shipping surcharge may apply for remote addresses. **For all BendPak brand two-post and four-post surface mounted lifts manufactured on or following 1/1/2011.
Limitation of Liability
In no event will either party be liable for any damage caused by the other party's failure to fulfill its responsibilities under these terms and conditions. In no event will either party be liable for any lost profits, lost savings, incidental damage, or other economic consequential damages. All expressed and implied warranties, including the implied warranties of merchantability and fitness for a particular purpose, are limited in duration to the coverage period. No warranties, expressed or implied, will apply after this period. BendPak may modify these terms and conditions at any time by either providing the customer with written notice or posting such revised terms on www.bendpak.com. Such revised terms shall be effective thirty days from the date of such written notice or posting.
|
|
|
 |
|
 |
|
|
| Accessories for this product... |
|
|
|
|
